Save this Search
     
Sort by:
  • Posted Date
Fixed Price: Not Sure   |  Posted: 2h, 28m ago  |  Ends: 14d, 21h  |   0 Proposals
My company is looking for licensed individuals or company that can install indoor and outdoor cameras in residental areas. We are located in New Jersey but if you're willing to travel please send a proposal. US only please apply.
Category: Electrical       

n****z87
 [?]
Sign in to view client's details.
| n****z87
|    United States
Fixed Price: Not Sure   |  Posted: 3h, 26m ago  |  Ends: 14d, 20h  |   4 Proposals
Summary: I need a pcb design for a small, light-weight, microprocessor-controlled, and easy to assemble transmitter to attach to small animals. Requirements ? Transmission should be in the band between 150.8 and 151.8 MHz. Each unit should have a different band separated by at least 10kHz (i.e. one transmitter might have a band of 150.890 and another 150.880). ? Weight less than 15 grams (ideally). The entire unit should be less than 1cm by 1cm. ? Range should be approximately 1Km ? Battery life should be a minimum of 3 months ? Pulse rate of approximately 1 pulse/second ? On-off controlled by tiny reed switch (magnetic) The units should be designed so that they can be easily constructed (using a tiny pcb as a base). There should be a set of 2 wire leads that would lead out to a small battery. A second lead should be for a wire whip-style antenna. I realize that there are commercial versions of this product available. I am looking for something that students can build on their own...
Category: Electrical       

s****hws
 [?]
Sign in to view client's details.
| s****hws
|    United States
Fixed Price: Less than $500   |  Posted: 6h, 20m ago  |  Ends: 14d, 17h  |   12 Proposals
architect design for 100 square meter apartment 3 bedrooms 2 bathroom. 1 kitchen. to get washington dc government approval
Category: Architecture       
Skills: 3D Modeling, ArchiCAD, Architecture       

v****df4
 [?]
Sign in to view client's details.
| v****df4
Fixed Price: Less than $500   |  Posted: 9h, 31m ago  |  Ends: 14d, 14h  |   7 Proposals
This is a Very simple breakout board that connects a cc3000 wireless module to a teensey 3.0 microcontroller along with the necessary supporting hardware (level shifter, power regulator, etc) All component configurations are open source, and this should be very simple to build. Needed: PCB/Gerber layout/design given schematic/BOM (  [obscured]  /YXXWQ9) and my desired component layout arrange PCB manufacture of 100 boards arrange component assembly/population for 50 of the 100 boards
Category: Electrical       

f****ous
 [?]
Sign in to view client's details.
| f****ous
|    United States
Fixed Price: $100 or less   |  Posted: 12h, 27m ago  |  Ends: 29d, 11h  |   4 Proposals
Create the Robot Structural Analysis file using the attached plans. It's a 7-storey, small RC old building in Imperial Units, i.e. ft, kip (1000 lb-f), etc. For elastic analysis only, and therefore no rebar details are necessary for input. Required inputs: (1) physical dimensions of Column, beam, slab, wall, staircase, water tank (2) Live load, dead load and wind load Must be completed in 7 days. Immediate one-off payment AFTER completion of job.
Category: Civil & Structural       

m****ung
 [?]
Sign in to view client's details.
| m****ung
|    Hong Kong SAR, PRC
Fixed Price: Not Sure   |  Posted: 14h, 0m ago  |  Ends: 2d, 10h  |   7 Proposals
Hi I'm doing exactly the same project (  [obscured]  /underground-cable-fault-distance-locator ) The only problem is that I need to replace the 8051microcontroller and ADC with the best microcontroller that it has ADC in it and it will do the same job?! The microcontroller I'm using is AT89S52 and outside ADC 8 bits ,single channel IC and take one analogy signal as input I need to replace them with a microcontroller that has built-in ADC, from ATMEL that is the same as AT89S52 but has ADC built-in
Category: Electrical       

I****m89
 [?]
Sign in to view client's details.
| I****m89
|    New Zealand
Fixed Price: $50 - $80   |  Posted: 14h, 18m ago  |  Ends: 1d, 9h  |   0 Proposals
I'm looking for someone who is knowledgeable of the REScheck Software Version 4.4.4 I need to generate a Envelope Assemblies table showing Gross Area, Cavity R-Value, Cont. R-Value, Glazing or Door U-Factor, UA. This should be a simple job if you know anything about Rescheck
Category: Other - Engineering &...       
Skills: 3D Modeling, Architecture, AutoCAD       

t****013
 [?]
Sign in to view client's details.
| t****013
|    United States
Fixed Price: $50 - $80   |  Posted: 14h, 35m ago  |  Ends: 1d, 9h  |   0 Proposals
I'm looking for someone who is knowledgeable of the REScheck Software Version 4.4.4 I need to generate a Envelope Assemblies table showing Gross Area, Cavity R-Value, Cont. R-Value, Glazing or Door U-Factor, UA. This should be a simple job if you know anything about Rescheck
Category: Civil & Structural       
Skills: 3D Modeling, Architecture, AutoCAD       

t****013
 [?]
Sign in to view client's details.
| t****013
|    United States
Fixed Price: $50 - $80   |  Posted: 14h, 36m ago  |  Ends: 14d, 9h  |   0 Proposals
I'm looking for someone who is knowledgeable of the REScheck Software Version 4.4.4 I need to generate a Envelope Assemblies table showing Gross Area, Cavity R-Value, Cont. R-Value, Glazing or Door U-Factor, UA. This should be a simple job if you know anything about Rescheck
Category: Architecture       
Skills: 3D Modeling, Architecture, AutoCAD       

t****013
 [?]
Sign in to view client's details.
| t****013
|    United States
Fixed Price: Less than $500   |  Posted: 15h, 48m ago  |  Ends: 2d, 8h  |   0 Proposals
Need a local architect to make plans for a pharmacy to submit to city of Huntington Beach. Small retail space, less than 1200sft, need plans according to local code for hassle free approval.
Category: Architecture       
Skills: Architecture, AutoCAD, Interior Design       
Preferred Location: United States

i****r99
 [?]
Sign in to view client's details.
| i****r99
|    United States
Fixed Price: Less than $500   |  Posted: 18h, 46m ago  |  Ends: 14d, 5h  |   7 Proposals
I have a small part designed that I would like to have a mold made. The part is slightly larger than 1 cubic inch. The mold can be made out of aluminum to save cost. It should be a simple 2 part mold, The 3D CAD file is complete, draft has already been factored in. I will be injecting the mold with a homemade machine I created. Summary - I need CNC machine services and someone with experience in mold machining to make an inexpensive yet perfectly functional mold.
Category: Other - Engineering &...       
Skills: CNC machining       

c****tis
 [?]
Sign in to view client's details.
| c****tis
|    United States
Fixed Price: More than $10,000   |  Posted: 19h, 17m ago  |  Ends: 25d, 2h  |   3 Proposals
Our company is a startup in the wearable technology space. While we cannot say much about our product, we need someone to help organize our management of components, and think through our options for logistics. The size of the product and dimensions of the packaging lend themselves to people with supply chain /mfg ops experiences in watches, jewelry, footwear, consumer electronics, mobile phones and fine foods. If you want to better understand the future of wearables, and want to work with vibrant, innovative environment, this opportunity might work for you. The team is a mix of experience and bold experimentation, located in San Francisco. PLEASE READ: You must be in the Bay Area to execute the tasks effectively.
Category: Contract Manufacturing       
Preferred Location: United States

O****eep
 [?]
Sign in to view client's details.
| O****eep
|    United States
Fixed Price: Not Sure   |  Posted: 20h, 29m ago  |  Ends: 14d, 3h  |   8 Proposals
We would like to design and manufacture a diesel monitor for marine diesel engines. The unit should monitor the amount of fuel been used. With a display the unit would show litres per hour used and total consumption. We also like to include the possabilty to be able to email results to an address. Also if we could incorporate live monitoring also?. The unit needs to be cost effective for small boats to buy. There is already plenty of expensive models on the market.
Category: Product Design       

t****sky
 [?]
Sign in to view client's details.
| t****sky
|    Ireland
Fixed Price: Less than $500   |  Posted: 20h, 38m ago  |  Ends: 14d, 3h  |   4 Proposals
I am in need of an inexpensive molding and manufacturing run of a simple item. The item measures @ 6.5 inch x 3 inch. I have attached an image that illustrates that the item is NOT solid plastic, but has open areas within these measurements. (The item resembles the letter "T" with a short leg. The leg has to be of a bendable plastic that could bend back to the Top of the "T". The center of the top of the "T" can be a rigid plastic). (2 separate plastic pieces glued together). I have an already existing Solidworks 3D file that will be sent to the winning bid for review and molding. All plastics types can be considered if they pass US import requirements for products. I have already been given initial mold pricing of ($600.00) from another company and am looking to beat that price. Assembled item pricing bid is currently at .15 cents per item. (Quantities are 5K+) If you can beat these prices by at least 20%, then please make a bid and send samples of ...
Category: Other - Engineering &...       

T****ury
 [?]
Sign in to view client's details.
| T****ury
|    United States
Fixed Price: $1,000 - $2,000   |  Posted: Apr 18, 2014  |  Ends: 24d, 21h  |   6 Proposals
I would like for a site to be developed and launched to facilitate car parts and accessories search based on the details of the vehicle. Further that when an inquiry is made by a customer, that the managing division of the company can view these queries via email etc to begin search and price the inquiry and then email it to the customer for purchase. (purchase option via paypal would be appropriate). Further details will follow concerning: Design Layout Logistics of Inquiries SMS Messaging to notify customer of their product tracking. Two More Aspects (Confidential)
Category: Other - Engineering &...       

d****rah
 [?]
Sign in to view client's details.
| d****rah *
|    Bahamas
Fixed Price: Less than $500   |  Posted: Apr 18, 2014  |  Ends: 13d, 22h  |   11 Proposals
I require a CAD/CAM designer that will design toy car models from a suitable 5mm plywood materials. The car will have freely moving wheels which will be attached to a motor and a battery. The drawing will be cut using a CNC laser machine and the software is TECHSOFT 2D DESIGN so they'll need to be compatible. The machine has a Red line for engraving and a black line to cut. This job is for the completion of one car model. The project has 4 phases: CAD stage, wheel stage, animation stage and sticker stage. At each stage there will be a thorough assessment of the work and I the successful designer must be willing to produce several drafts until the perfect model is produced. I need time and thought put into this project . Attached is a document explaining the project in greater detail.
Category: CAD       
Skills: 3D Modeling, AutoCAD, SolidWorks       

w****ces
 [?]
Sign in to view client's details.
| w****ces *
|    United Kingdom
Fixed Price: Not Sure   |  Posted: Apr 18, 2014  |  Ends: 13d, 21h  |   0 Proposals
Hi all, Please read entirely before applying. Looking for a US based contract manufacturer to produce, firstly, a prototype and then hopefully units in bulk order. We have a working prototype currently but are aiming for high quality. The materials include rubber, wood grain (rosewood preferably), and aluminum as the main portion. Also, there are a few portions that need to be print painted in gold color We have all files necessary for printing. Good luck!
Category: Contract Manufacturing       

R****ses
 [?]
Sign in to view client's details.
| R****ses
|    United States
Fixed Price: Less than $500   |  Posted: Apr 18, 2014  |  Ends: 13d, 13h  |   4 Proposals
I'm looking for someone who has experience designing high pressure systems and understands supercritical CO2 extraction. I would like a pneumatics diagram and solid model of a 5L, 5000psi capacity system with dual separators.
Category: Mechanical       

M****ica
 [?]
Sign in to view client's details.
| M****ica
|    United States
Fixed Price: $1,000 - $5,000   |  Posted: Apr 18, 2014  |  Ends: 24d, 5h  |   7 Proposals
I need a Quality engineer based in shenzhen or Singapore to support the following activities: - Oversee moulding tool trial at our China supplier - Make sure all parts are in spec - Complete QA checks on all parts and sub assemblies - Measurement reports - Liaise with client You must have the following skills: - 2 years+ in working in quality or supply chain - experience working with tooling for plastics, metal stamped parts, adhesives & gaskets - Implementing QA processes into suppliers - Speak Mandarin & Good English (read & write)
Category: Mechanical       
Skills: Mechanical Engineering       

a****yed
 [?]
Sign in to view client's details.
| a****yed *
Fixed Price: Not Sure   |  Posted: Apr 17, 2014  |  Ends: 13d, 3h  |   0 Proposals
Looking to have a site with a landing page opt-in builder that works along with aweber and getresponce. This will not use the form from aweber or getresponce but the html script for the campaign can be put into the builder for custom forms with in the landing page builder that people have to sign up and be a member to use free. Must know what you are doing. I don't want bugs forever on this thing.
Category: Product Design       
Skills: Application Programming, AWeber       

s****la2
 [?]
Sign in to view client's details.
| s****la2
|    United States
Fixed Price: $50 - $150   |  Posted: Apr 17, 2014  |  Ends: 13d, 3h  |   12 Proposals
I need someone that is experienced in Eagle CAD to make a change to an existing PCB. This change consists of hooking up three new low power MOSFETs, adding 0603 three resistors, and rewiring a couple of nets. I will provide both the eagle schematic and PCB, plus a pdf of the new schematic with the changes highlighted. If we are happy with the results, this will probably lead to future jobs too. I'm a circuit designer but I'm not very good with Eagle. So no circuit design experience needed, just lots of experience laying out printed circuit boards with Eagle CAD. Thanks.
Category: CAD       
Skills: OrCAD, Electronics, PCB Design       

J****lEE
 [?]
Sign in to view client's details.
| J****lEE
|    United States
Fixed Price: Less than $500   |  Posted: Apr 17, 2014  |  Ends: 13d, 1h  |   17 Proposals
I am looking for a 3D animator that can create animations, cutaways, and simulators designed to show how a particular piece of equipment works, and the major components of a piece of equipment Equipment Types: AC Motor Centrifugal Pump Reciprocating Compressor Multi-Stage Compressor Axial Pump Wind Turbine Simple Cycle Gas Turbine Simple Cycle Steam Turbine Paper Machine Converting Machine Positive Displacement Pump Rolling Element Bearings Sleeve Bearings Different types of shaft misalignment Simulators- Would include a variety of things that we can discuss after the models are complete. These animations and simulators will be added to training materials I have developed within Articulate Storyline and Presenter. Please submit at least one example of your work. This will be a long-term engagement depending on the quality of the first animation. As a fellow freelancer I'm looking for someone who is as dedicated to detail and customer satisfaction as I am. Important: You are bid...
Category: 3D Modelling       
Skills: 3D, Animation       

m****mrp
 [?]
Sign in to view client's details.
| m****mrp
|    United States
Symbol Key
Payment method not yet verified
Payment verified
Purchased $1-$500
Purchased $500-$5,000
Purchased more than $5,000
You have already submitted a
proposal to this job