Save this Search
     

All JobsEngineering & ManufacturingHourly

 (261 results)  
Sort by:
  • Posted Date
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: May 19, 2015  |  Ends: 9d, 20h  |   21 Proposals
This project entails a battery powered motor control embedded system. The primary need for this project is the software for controlling the motors. However, the ideal candidate can develop the hardware required for controlling the system. This is relatively simple, there isn't a lot of circuitry other than voltage regulation and motor control. Motor options: - DC Brushless - Stepper - Other? Hardware: - H-Bridge or other - Voltage Reg (Switching) - Position sensing components (potentiometer, etc) Processor Options: - AVR - ARM Tags: Feedback Controls, PID, Motor Controller, H Bridge
Category: Electrical       

p****332
 [?]
Sign in to view client's details.
| p****332
|    United States
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: May 18, 2015  |  Ends: 9d, 16h  |   5 Proposals
Hello there, My name is Drew & I design and work with analog video circuitry. I have a basic understanding of electronic circuit design, very basic, I am self taught. On my most recent design I've run into a problem that I cannot really explain and I am looking to get a professional take on my trouble. Long story short, I have a small video fx processor. On top of being a cool analog video device with a bunch of control knobs it features an audio input function. I have an audio input going to a TIP31 bipolar junction transistor which is amplifying my audio signal and driving my LED light to the db of the incoming audio signal. The goal is for this LED to be the LED portion of a vactrol. Upon driving the LED everything behaves as it should until suddenly at an unpredictable moment, while noodling around with the fx knobs on my unit (perhaps the LED lighting in conjunction with a particular knob position), the whole board goes bad. By bad I mean the LED keeps on blinking... but ...
Category: Electrical       

d****-m1
 [?]
Sign in to view client's details.
| d****-m1
|    United States
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: May 18, 2015  |  Ends: 9d, 13h  |   9 Proposals
I need to set up the sections of a building, according to wind loads and quake loads. I just need help doing this. Although I have the instructions, I need to make sure I do it right. Thank you
Category: Civil & Structural       

j****mon
 [?]
Sign in to view client's details.
| j****mon
|    United States
Hourly Rate: $10 - $15 / hr   |  Duration: 7-9 months  |  Posted: May 18, 2015  |  Ends: 9d, 10h  |   1 Proposal
Looking for an electronic technician with experience in soldering and assembly of electronic components as well as maintaining and tracking inventory. Must be located in DC metro area. Job site is located in Alexandria, VA
Category: Electrical       
Preferred Location: United States

g****usi
 [?]
Sign in to view client's details.
| g****usi *
|    United States
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: May 18, 2015  |  Ends: 9d, 10h  |   19 Proposals
This is a 2-4 Layer PCB layout project that has mechanical parts, and mounting components, which means we need someone with great mechanical expertise. The electrical design is complete, so the primary section is the mechanical. I need someone to design the mechanical mounting, then the selection and placement of the mechanical components which will integrate with the PCB. This is why having PCB experience is important. If you have an electrical engineering background, you'll also fit for the schematic capture project as well. Please let me know which applies to you.
Category: Other - Engineering &...       
Skills: Altium Designer, 3D Design       

p****332
 [?]
Sign in to view client's details.
| p****332
|    United States
Hourly Rate: Less than $10 / hr   |  Duration: Not Sure  |  Posted: May 18, 2015  |  Ends: 9d, 9h  |   33 Proposals
I need an architect to draw a plan for my house. It is for for residential purposes. Please let me know if you can draw such a plan. I am looking to build a house similar to one attached. I want want a 3d model as well.
Category: Architecture       
Skills: 3D Modeling, Architecture, AutoCAD       

r****x23
 [?]
Sign in to view client's details.
| r****x23
|    Guyana
Hourly Rate: $15 - $20 / hr   |  Duration: Not Sure  |  Posted: May 18, 2015  |  Ends: 1d, 9h  |   25 Proposals
We are looking for someone who can draw architectural and interior cabinetry details for our projects, in AutoCAD. We mainly design restaurants but sometimes exterior details for a facade maybe required. We would provide interior plans, elevations and 3D model views. We would also provide some drawings of previous details example on CAD and/or sketches. Your job would be to produce sections of walls, cabinets, counters, soffits, benches and such, as needed. This will be hourly job per project. So we are looking for someone who wants to work a few hours a week to start with. Understanding of materials thicknesses, attachments and US measurements required. Previous experience in details required! Please reply with some example of a section through a wall and a counter that you have done before. Hourly payment may depend on experience and may go over of below what is shown here. Thank you and looking forward to your reply! EK
Category: Architecture       
Skills: Architecture, AutoCAD       
Preferred Location: North America

S****mes
 [?]
Sign in to view client's details.
| S****mes
|    United States
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: May 18, 2015  |  Ends: 9d, 9h  |   3 Proposals
Joy Stick integration. I have existing joystick consoles that need modification and extensive upgrades.
Category: Electrical       
Skills: Electronic Design       

k****low
 [?]
Sign in to view client's details.
| k****low
|    United States
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: May 18, 2015  |  Ends: 9d, 9h  |   0 Proposals
Joy Stick integration. I have existing joystick consoles that need modification and extensive upgrades.
Category: Electrical       
Skills: Electronic Design       

k****low
 [?]
Sign in to view client's details.
| k****low
|    United States
Hourly Rate: $20 - $30 / hr   |  Duration: Not Sure  |  Posted: May 18, 2015  |  Ends: 9d, 8h  |   67 Proposals
We are looking for a Mechanical Design Engineers preferably experienced in manufacturing industry. Due to work overload of our design engineers we are forced to seek outsourced services. I case of a satisfactory cooperation we provide a possibility for constant job provision. Expert knowledge of 3D CAD software (preffered SolidWorks or CATIA) is required. Solid understanding of design for manufacturing is welcomed. Enclosed you'll find our company presentation. When responding to this post please include images of your work. Start date a.s.a.p.
Category: Mechanical       

k****ech
 [?]
Sign in to view client's details.
| k****ech
|    Slovak Republic
Hourly Rate: Not Sure   |  Duration: 1-2 weeks  |  Posted: May 18, 2015  |  Ends: 1d, 7h  |   19 Proposals
We seek a professional to design a 2-story porch addition for our home. Our goals along with key elements, pictures and drawings from a 2007 remodel are in this Google Doc.   [obscured]  /document/d/1Y3j-traKpgjgVWH8PQtPhHzvcan1C_F-HmPkl0YckDY/edit?usp=sharing We are open to creative ideas outside what is shown in the line drawn mock-up (done in sketchup). We love good design and lean toward more contemporary as can be seen in the Houzz ideabook linked. Lot coverage is a concern also since the backyard is fairly small and there are coverage limits per local zoning regulations. Please bid on the first phase only which is the general design. The 2nd phase will be the drafting of the actual formal drawings which will be used to get approval from our local architectural review board and used by the contract(s). This is being posted as an hourly job but if you would prefer to bid this as fixed rate note this in your bid. Please ask questions. Thank you.
Category: Architecture       
Skills: Architecture, AutoCAD, Interior Design       

C****aul
 [?]
Sign in to view client's details.
| C****aul
|    United States
Hourly Rate: Not Sure   |  Duration: 3-4 weeks  |  Posted: May 18, 2015  |  Ends: 9d, 5h  |   6 Proposals
We are a small startup and we have prototypes of a patent pending product. You will be programming with the RTOS ThreadX. This project will be focus on two parts: a bootloader that is loaded from EEPROM that verifies the firmware in SPI Flash (code signing) AND the main firmware that performs RAID across two microSD cards and provides functionality for separate read-only and read-write functionality via a high-speed differential switch and signal redrivers. The main CPU is an ARM926 from Cypress. The CPU manufacturer provides example code for both parts of the project. We will be building from scratch or incorporating a preexisting anti-virus package that will scan data as it is being written or after it is written to the microSD storage. We have a few prototypes that we would like to send to the selected programmer in order to program via J-link over JTAG. We are currently having some troubles with this portion of the project.
Category: Other - Engineering &...       
Preferred Location: North America, Western Europe, Australia/Oceania

d****yco
 [?]
Sign in to view client's details.
| d****yco
|    United States
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: May 18, 2015  |  Ends: 8d, 23h  |   25 Proposals
In order to validate the functionality of all components of my circuit, I am looking for a circuit and PCB designer which can do the circuit refine, design and prepare the PCB boards. To give you a general overview of the circuit: it is basically the whole supply of the circuit which consist of a solar-cell charger and a 9V battery which must provide us a 3.3V output for the micro-controller, a 5 V and 100mA to drive a solenoid and a 5V and 500 mA for a USB charger. I have used 3 ICs made by Linear Technology, which I can provide you with all their datasheets and information if it is needed. Regards, Sanaz Haddadian
Category: Electrical       

S****adn
 [?]
Sign in to view client's details.
| S****adn
|    Germany
Hourly Rate: $15 - $20 / hr   |  Duration: Not Sure  |  Posted: May 17, 2015  |  Ends: 8d, 10h  |   57 Proposals
Scope : 3D modeling and manufacturing drawings Small industrial machine with extruded aluminum frame. We will provide sketches and conceptual design models. Prefer SOLIDWORKS 2014+ and someone with machine design experience.
Category: 3D Modelling       

S****TOK
 [?]
Sign in to view client's details.
| S****TOK
|    United States
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: May 17, 2015  |  Ends: 8d, 9h  |   11 Proposals
My partner and I have been working on a new electronic product and are in need of some outside assistance. In particular we are looking for someone to help us with the electromechanical side. So far we have been working with parts purchased from adafruit.com to put together a piece of hardware capable of doing what we need. -Rasperi pi A+ -5" screen -Lio battery -Battery charge board -Small bluetooth board -Screen driver board In the research we have done it has come to our attention that custom boards can be made that can do exactly the same thing. We feel this may be our best option considering it would help keep the overall form factor of the product small, which is very important for us. Any and all applicants must be willing to sign a Nondisclosure agreement. While we are located upstate new york new poughkeepsie we are more than willing to come down to the city to complete our project. Please contact us with any questions you may have.
Category: Product Design       

p****ons
 [?]
Sign in to view client's details.
| p****ons
|    United States
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: May 17, 2015  |  Ends: 8d, 7h  |   13 Proposals
Hi, I need ASIC designer to make ASIC chips design. Will PM with you the details. You can work solo or with your team, and after this project is done we can hire you to join our team if you want.
Category: Electrical       

a****u75
 [?]
Sign in to view client's details.
| a****u75
|    United States
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: May 17, 2015  |  Ends: 53d, 6h  |   2 Proposals
I have recorded a vocal lead, but it sounds "just good" at best. I am seeking a "pitch correction" enginer who can modify the pitch curve of my vocal, to make it sound controlled and flawless. That is, I am not only asking for basic pitch tuning, but more advanced editing to the pitch curve, so that the vocal sounds remarkable - without the static robotic effect. It is very hard to find these types of engineers. Is this something that falls into your expertise? Contact me! Short snippet of the vocal:   [obscured]  /inherent90/demo-snippet/s-agaVJ
Category: Other - Engineering &...       

i****t90
 [?]
Sign in to view client's details.
| i****t90
|    Sweden
Hourly Rate: Not Sure   |  Duration: 3-4 weeks  |  Posted: May 17, 2015  |  Ends: 8d, 3h  |   18 Proposals
I already have a high quality 3-D printed prototype of my device, but feel that it could benefit from some additional design work. The prototype was not simply an assembly of the 3-D printed parts, as there were some customized components that the original industrial design firm incorporated into the model. I am quite pleased with the prototype. The prototype was designed in Solidworks, and could be the basis for the next round for design. I have the SolidWorks files and additional design/patent drawings that could be shared with the selected individual
Category: Product Design       
Preferred Location: North America

b****er1
 [?]
Sign in to view client's details.
| b****er1
|    United States
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: May 17, 2015  |  Ends: 8d, 3h  |   18 Proposals
I'm looking to get a custom pcb printed with a few requirements: something i can run arduino code on (atmega or other) maximum 5/8 inch wide bluetooth adapter 3 axis motion sensor ir receiver microSD or other external memory
Category: Product Design       
Skills: PCB Design       

d****anz
 [?]
Sign in to view client's details.
| d****anz
|    United States
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: May 16, 2015  |  Ends: 7d, 14h  |   3 Proposals
My HVAC company provides HVAC, EMS, and building automation service. Need individual to provide expertise leading to my company becoming certified for NEBB or AABC. Must be able to apply and meet standards to above organizations for membership in USA .Please contact for more details. 501-514-5896 Central Time Zone
Category: Other - Engineering &...       

l****ore
 [?]
Sign in to view client's details.
| l****ore *
|    United States
Hourly Rate: $20 - $30 / hr   |  Duration: 1-2 weeks  |  Posted: May 16, 2015  |  Ends: 7d, 14h  |   7 Proposals
I need to have a Texas Intruments CC2531 Zigbee dongle (USB connection) configured to work with a Beaglebone Black development board running Linux. Drivers for the CC2531 are available for download on the Texas Instruments website. Once set up the proof of working must be turning on and off a supplied Zigbee enabled LED light bulb by means of one of the buttons on-board the Beaglebone. I would supply the Beaglebone Black, CC2531 dongle, Zigbee LED bulb and Texas Instruments CC Debugger. You provide a simple written outline of the steps that were taken for the setup. Please estimate how many hours this will take. Thank you.
Category: Electrical       

m****000
 [?]
Sign in to view client's details.
| m****000
|    United States
Hourly Rate: $15 - $20 / hr   |  Duration: 1-3 months  |  Posted: May 16, 2015  |  Ends: 7d, 10h  |   22 Proposals
Revit 2015 & AutoCAD Proficiency is a must ? Orange County, CA firm seeks a part time, work from home operator for various design consulting projects. Candidates must have a solid understanding of collaboration in Revit 2015 and as an AutoCAD drafter for systems design and or similar type of work. Candidates must have experience with, or a working knowledge of, MS Office (Word, Excel, and Outlook). Candidates must be able to follow directions from Lead Designers, take red lines to black, work from sketches, set up borders, layers and title blocks in AutoCAD and set up projects, views and sheets in Revit, enable all required linking and work with families.
Category: CAD       
Skills: AutoCAD, AutoDesk Revit       

P****ins
 [?]
Sign in to view client's details.
| P****ins
|    United States
Symbol Key
Payment method not yet verified
Payment verified
Purchased $1-$500
Purchased $500-$5,000
Purchased more than $5,000
You have already submitted a
proposal to this job