Save this Search
     
Sort by:
  • Posted Date
Hourly Rate: Not Sure   |  Duration: 1-3 months  |  Posted: 46 minutes ago  |  Ends: 14d, 23h  |   1 Proposal
The project is to design approx 16 townhouses on a block of land in a small 3600m2. Each townhouse shall include - 3 bedrooms (3x3m for 2nd and 3rd bedroom, main room a little larger) - 2.5 bathrooms (1 ensuite, toilet downstairs, family bathroom with bath) - Kitchen, living and dining room in an alfresco arrangement - single or double garage (6m x 3m for single, 6m x 5.7m for double) - Laundry - Double story Total living area (not including garage) is to be less than 100m2. The land has a gradient on it that make approx 7m over 100m. Retaining walls will have to be shown on the plans that are a maximum of 1m high but can be stepped at 1m from each other in areas that need it. Ideally fill and cut material will be equal. Backyards to have a minimum 36m2 area. An area of 4m x4m must receive sunlight for 3hrs on the winter solstice. The land has three frontages but only two can be used for driveways. The frontage with driveways are 45m and 20m. The design must comply with   [obscured]  
Category: Architecture       
Skills: 3D Modeling, Architecture, AutoCAD, Home Design       

T****eng
 [?]
Sign in to view client's details.
| T****eng
|    Australia
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: 3h, 1m ago  |  Ends: 14d, 20h  |   3 Proposals
Looking for someone to write bid proposal for land surveying and civil engineering jobs. If I like your work this will become a regular thing.
Category: Civil & Structural       
Skills: ANSYS, AutoCAD, Civil Engineering       

e****726
 [?]
Sign in to view client's details.
| e****726
|    United States
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: 4h, 42m ago  |  Ends: 14d, 19h  |   7 Proposals
Hey Greg are you avail abel to complete some plans i had done by a freelancer over seas that they cant make the changes to, and i have a tight deadline, ? let me know? about 3-4 hours i think???
Category: Architecture       
Skills: 3D Modeling, Architecture, AutoCAD       

j****oft
 [?]
Sign in to view client's details.
| j****oft
|    Australia
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: 5h, 3m ago  |  Ends: 14d, 18h  |   5 Proposals
we are looking for a engineer or draftsman to design and detail light gauge steel house frames, we currently use truss d&e but anyone with experience in : Vertex : Framecad : any other This will be ongoing work on a long term basis.
Category: CAD       

j****100
 [?]
Sign in to view client's details.
| j****100
|    Australia
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: 10h, 45m ago  |  Ends: 14d, 13h  |   7 Proposals
Sketches for a Product Design. I will provide the information for a product. I need many different sketches for a demo presentation of the product. This is more an illustration need rather than a real product development, nevertheless, the project is intended to end with a concept of product to be manufactured. This is a kitchen appliance.
Category: Product Design       
Preferred Location: United States

f****ejo
 [?]
Sign in to view client's details.
| f****ejo
|    United States
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: 11h, 27m ago  |  Ends: 6d, 12h  |   2 Proposals
We have a spinning display (prototype) which has a 7" display, motor to spin our product and using an Olimex board to run the video / audio. We have successfully prototyped this and now, we need a freelancer to optimize this design and prepare it for manufacturing as the cost is too high using the Olimex board and the associated 7" LCD/controller board. We are using a standard microwave oven motor to independently spin our product and this is directly connected to a switch and powered directly to an AC power source. The motor turns 360 degrees and then automatically reverses since we have created a mechanical stop. The way the unit will function is as follows: 1) User will turn on a power switch located on the bottom of the display 2) Display will provide power to the motor which will start spinning and simultenously power the microcontroller board to run the OS (i.e. Linus/Android). 3) OS will initiate and the user will see a splash screen which will allow them to e...
Category: Electrical       

p****one
 [?]
Sign in to view client's details.
| p****one
|    United States
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: 17h, 43m ago  |  Closed  |   3 Proposals
Greetings, I need to convert a PDF layout to a Sketchup Floorplan Layout that I can edit. You can suggest other programs, I just thought Sketchup would be ideal because it's free and I don't own CAD. This is for a non-profit so I am operating on a small budget. It seems like Sketchup defaults to 3D. I notice a lot of layouts going that direction. To be honest, I think that would be overkill for this project. The purpose of the room layout is to show the convention space and where each person is sitting and what they ordered (table sizes, electricity, floodlights, chairs,skirting). Each square is a 10'x10' vendor booth.There are approximately 60-70 10'x10' booths (squares on layout). I will send the dimensions of the room. Each booth shows if they have a floodlight (denoted by X). The "E" denotes electricity. Solid line is pipe/drape (all it is, is a separator). A dash is no pipe/drape. CHR denotes the number of chairs per booth. It would be nice to have re-usable ta...
Category: CAD       

j****g21
 [?]
Sign in to view client's details.
| j****g21
|    United States
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: 17h, 59m ago  |  Ends: 14d, 6h  |   3 Proposals
Hi, I am looking into creating my custom mirror Photo Booth. However i don't know exactly what i needed to replicate it. Below you will find some photos of people who have done it before. What i need is for someone to look into what equipments i will need to purchase and provide me with exactly what material i need to buy/use for the mirror etc..   [obscured]     [obscured]     [obscured]  /products/mirror-me-booth/?gclid=Cj0KEQjwyoCrBRCl-aa97pKX_t8BEiQAbrs_9Fso3TPCLvXafZlu-ycUWG1QdBQmMVlN87pPED87tzMaAmZc8P8HAQ
Category: Product Design       

P****Glo
 [?]
Sign in to view client's details.
| P****Glo *
|    Qatar
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: 21h, 29m ago  |  Ends: 6d, 2h  |   15 Proposals
We're a lifestyle brand that specialises in premium technology accessories and we're looking for an experienced 3D Product Designer to render our product images. We require 3D renders of our product that is photo realistic and looks beautiful to look at. For this project you'll be working on 1 product that comes in 2 colours, which are Black and Brown. Here is an example of the type of quality and images we require:   [obscured]  /mediaroom/portfolio/leather-wallet-case-80-iphone-6-tan-studio/ We require: - 5 Images on a white background We will send you the details of our product in more detail. Please feel free to apply for this project if you feel you're confident to deliver this type of quality. We look forward to seeing your proposals.
Category: 3D Modelling       
Skills: 3D Modeling, 3D Design, 3D Rendering       

s****iah
 [?]
Sign in to view client's details.
| s****iah
|    United Kingdom
Hourly Rate: $15 - $20 / hr   |  Duration: Not Sure  |  Posted: 22h, 49m ago  |  Ends: 14d, 1h  |   9 Proposals
I need to simulate a pre-curved tube being rotated inside a straight tube by 90 degrees. I need pictures and a video of the simulation. I also need the position of the end bit of the combined tubes relative to a (0,0,0) axis. To be completed asap. This should not take long for an expert. I have a working file that I need to modify, it is in Abaqus 6.14 I need a video of the simulation, pictures and a good meshing. Description of the process you use is also required. If you use on-screen recording, it's even better
Category: 3D Modelling       
Skills: Abaqus, meshing       

D****e13
 [?]
Sign in to view client's details.
| D****e13
|    Australia
Hourly Rate: $30 - $40 / hr   |  Duration: 1-2 weeks  |  Posted: May 23, 2015  |  Closed  |   6 Proposals
I have an assignment that I need help with. I have 25 statistics related problems that I need solved within an hour. I will give you the problems after you have agreed to the job. I assure you, they are all statistics related and some are multiple choice. You will receive payment immediately upon completion of the assignment.
Category: Other - Engineering &...       
Skills: Mathematics       

c****pjr
 [?]
Sign in to view client's details.
| c****pjr
|    United States
Hourly Rate: $10 - $15 / hr   |  Duration: Not Sure  |  Posted: May 23, 2015  |  Ends: 13d, 14h  |   5 Proposals
I want a miniature PSU (transformerless) design which can deliver dc output from a 100-250VAC input to charge a a li-poly battery correctly. Battery capacity is 8000mah- 12000mah. PSU side need to be >80% effeiceny in power conversion to the li poly charging circuit and will need a 4 level LED fuel gauge indication for the battery status. The circuitry need to be with as few components as possible, preferrable a 2 ic solution and lowest BOM cost solution. pls propose possible ic selection for us to make estimate BOM cost.
Category: Electrical       
Preferred Location: Eastern Europe, India/Southern Asia, Eastern Asia

v****whk
 [?]
Sign in to view client's details.
| v****whk
|    Hong Kong SAR, PRC
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: May 22, 2015  |  Ends: 13d, 13h  |   8 Proposals
I have plans to build 2x 12x3m buildings which need the materials Qty to be taken off. This only includes the extra work for the buildings ie the steel frame the building is suspended on. It also includes such things as the amount of concrete required, the steel frame and also timber decking qty and stairs details. This must be itemized: 1. Additional Steel Structure 2. Veranda 3. Stairs
Category: Other - Engineering &...       

R****tag
 [?]
Sign in to view client's details.
| R****tag
|    Australia
Hourly Rate: Not Sure   |  Duration: 1-3 months  |  Posted: May 22, 2015  |  Ends: 1d, 9h  |   2 Proposals
We are seeking an experienced profession to work with the working group in (1) formulating a position, (2) researching data to support the position, and (3) create appropriate documents articulating the position and advocating for the community to county officials. Learn more:   [obscured]  /redir?page=view&resid=43E294656599B3FF!148706&authkey=!ADKnxTGAeoekkEw
Category: Civil & Structural       

S****irs
 [?]
Sign in to view client's details.
| S****irs
|    United States
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: May 22, 2015  |  Ends: 13d, 9h  |   12 Proposals
Hi, I would like to have a PCB ready for print after simulation with some sensors conneted to it, need some one that families with Arduino pro mini + esp8266 hardware
Category: Electrical       

a****asa
 [?]
Sign in to view client's details.
| a****asa
|    Denmark
Hourly Rate: $10 - $15 / hr   |  Duration: 4-6 months  |  Posted: May 22, 2015  |  Ends: 5d, 8h  |   7 Proposals
We need tutor to teach micro electroncs for following topics. 1.Semi conductor fundamentas. 2.Career Modelling 3.Carrer action. 4.PN Diode,BJT, ...etc Text book:Semi conductor Device fundamentals by Robert E Pierret Addision wesley publication
Category: Electrical       

s****jan
 [?]
Sign in to view client's details.
| s****jan
|    United States
Hourly Rate: $40 / hr or less   |  Duration: Not Sure  |  Posted: May 22, 2015  |  Ends: 13d, 4h  |   24 Proposals
PLEASE READ! I am looking for an engineer who can create the inner workings of a new Blender Idea I have. An NDA has to be signed and this is a for-hire job unless I find a great engineer and we can discuss a small partnership in the idea. I will be giving you a concept and you will give me how my concept can realisticly work with designs and how the mechanics make it work so i can submit to a manufacture. Please be creative and understand how Blenders rotate and spin
Category: Mechanical       
Skills: 3D Modeling, AutoCAD, Electrical Engineering       

c****est
 [?]
Sign in to view client's details.
| c****est
|    United States
Hourly Rate: $10 - $15 / hr   |  Duration: 4-6 months  |  Posted: May 22, 2015  |  Ends: 13d, 1h  |   1 Proposal
Hi, We're a UK based footwear manufacturer and retailer. We're looking for someone to search and source manufacturers in Europe for a number of private label products. Tasks will include - thorough online research to find product suppliers - contacting and liaising with manufacturers - making sourcing decisions - negotiating costs and production schedules Opportunity for additional design related responsibility and input into brand product design and selection. Preferred attributes of candidates - - Experience and understanding of the buying and sourcing process - Candidates based in Europe as the majority of our suppliers are Europe based - Candidates based in Portugal/Spain or UK is preferable - Knowledge of Portugal/Spain manufacturing regions - Multilingual - Portugese/Spanish ideally - Can Google
Category: Product Design       

h****orc
 [?]
Sign in to view client's details.
| h****orc
|    United Kingdom
Hourly Rate: $10 - $15 / hr   |  Duration: 4-6 months  |  Posted: May 22, 2015  |  Ends: 13d, 1h  |   1 Proposal
Hi, We're a UK based footwear manufacturer and retailer. We're looking for someone to search and source manufacturers in Europe for a number of private label products. Tasks will include - thorough online research to find product suppliers - contacting and liaising with manufacturers - making sourcing decisions - negotiating costs and production schedules Opportunity for additional design related responsibility and input into brand product design and selection. Preferred attributes of candidates - - Experience and understanding of the buying and sourcing process - Candidates based in Europe as the majority of our suppliers are Europe based - Candidates based in Portugal/Spain or UK is preferable - Knowledge of Portugal/Spain manufacturing regions - Multilingual - Portugese/Spanish ideally - Can Google
Category: Contract Manufacturing       

h****orc
 [?]
Sign in to view client's details.
| h****orc
|    United Kingdom
Hourly Rate: $20 - $30 / hr   |  Duration: Not Sure  |  Posted: May 22, 2015  |  Ends: 13d, 1h  |   8 Proposals
I have a new magic idea, and i need a tech engineer that collaborate to create the new revolutionary Ring that vibrate and have a LED for notifications. and bluetooth The item price should be very cheap, and accessible to all ages I will give you all details and discuss about the price. This is the next big thing
Category: Mechanical       

V****ato
 [?]
Sign in to view client's details.
| V****ato
|    Italy
Hourly Rate: $20 - $30 / hr   |  Duration: Not Sure  |  Posted: May 22, 2015  |  Closed  |   0 Proposals
I have a new magic idea, and i need a tech engineer that collaborate to create the new revolutionary Ring that vibrate and have a LED for notifications. I will give you all details and discuss about the price. This is the next big thing
Category: Mechanical       

V****ato
 [?]
Sign in to view client's details.
| V****ato
|    Italy
Hourly Rate: $10 - $15 / hr   |  Duration: 1-2 weeks  |  Posted: May 22, 2015  |  Ends: 12d, 23h  |   6 Proposals
Hi, I am looking for someone to put a planning application together for a new window to fit into an existing house. The property is situated in Auckland, New Zealand so some insight into New Zealand planning regulations may be handy but not absolutely necessary. I already have some CAD drawings of the property but these will need to be worked up to a higher level. I also have the original drawings which can be used along with photos to complete the propose drawings. I will require 1 site plan 2 x floor plans Elevations and any other documents which will be required.
Category: Architecture       
Skills: 3D Modeling, Architecture, AutoCAD       

a****ton
 [?]
Sign in to view client's details.
| a****ton
|    United Kingdom
Hourly Rate: $15 - $20 / hr   |  Duration: 1-2 weeks  |  Posted: May 22, 2015  |  Ends: 12d, 19h  |   16 Proposals
We are looking at converting our current library of products from Solidworks 3d models to REVIT models for use in the architectural industry. Applicant should have experience in the Architectural field to ensure the REVIT models offer relevant information. There are around 100 items that need to be converted. Candidate should offer and efficient way converting files without having to redraw each item. There is a Solidworks part available for downloading which can be used to see what is required to convert the files.
Category: 3D Modelling       
Skills: Autodesk Inventor, AutoDesk Revit       

C****lor
 [?]
Sign in to view client's details.
| C****lor
|    South Africa
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: May 21, 2015  |  Ends: 12d, 13h  |   13 Proposals
We have a project that requires the production of a 3D model from two sets of existing fabrication drawings, and the creation of new fabrication drawings. We would prefer Tekla be used for purposes of exporting the files to our CNC machines. As part of the work product, we require an accurate bill of materials be produced on the new set of fabrication drawings. The existing fabrication drawings require additional details and work to the point where we believe it is better to re-produce the model and drawings. However, the fabrication drawings are good enough to use to re produce a model and fab drawings to more accurately reflect the detail of each steel member/part. Our company does not currently have the availability to do it, as it is something we would need completed by Wednesday May 27.
Category: 3D Modelling       
Skills: 3D, Tekla Structures       

j****ant
 [?]
Sign in to view client's details.
| j****ant
|    United States
Symbol Key
Payment method not yet verified
Payment verified
Purchased $1-$500
Purchased $500-$5,000
Purchased more than $5,000
You have already submitted a
proposal to this job