Save this Search
     
Sort by:
  • Posted Date
Mechanical
Fixed Price: Less than $500   |  Posted: 12h, 29m ago  |  Ends: 14d, 11h  |   12 Proposals
Very simple steel structure for which I have attached a hand sketch. -consider a roof snow load of 25 pound per square foot -roof dead load of 15 pounds per square foot -ultimate wind velocity 120 miles per hour I need the wind and and snow load for the structure using ASCE 7-10 Also check the capacity of the four columns and four beams if they are made from the following material:   [obscured]  /merchant.cfm?pid=18019&step=4&showunits=inches&id=1270&top_cat=0
Category: Civil & Structural       
Skills: Civil Engineering, Structural Analysis       

j****tay
 [?]
Sign in to view client's details.
| j****tay
|    United States
Fixed Price: Not Sure   |  Posted: 13h, 58m ago  |  Ends: 6d, 10h  |   2 Proposals
Hello! Thank you for considering this job. I am working with a friend to build a coffee stand (espresso stand) from the ground up. What I need is a few of ideas or schematics to work with for several different locations. Two of the locations require thin but long coffee stands. And one location has all the space you can imagine for a free standing espresso stand. I would imagine the stands being anywhere from 12 feet long to 6 feet wide, approximately. Preferably, I need someone who is familiar with doing this type of café/coffee stand design ? and who can help design the space for the stands which would include space for an espresso machine, grinders, storage, refrigerator double-sided windows, etc. I should be able to give the schematics to a contractor who would then be able to build the stand using what I gave them. The stand should be self-contained, plumbed (If water is available), and able to transport on a trailer. Im a total novice at this, so any other advice may ...
Category: Civil & Structural       

v****gns
 [?]
Sign in to view client's details.
| v****gns
|    United States
Fixed Price: $1,000 - $5,000   |  Posted: 16h, 26m ago  |  Ends: 25d, 5h  |   3 Proposals
I am using a CFD program CONVERGE to simulate engine operation. The compression chamber has small leak passages, on the order of 1mm^2, from which the compressed gas leaks during the engine cycle. Modeling these leaks is inefficient due to the small mesh size required, and this slows the simulation computing time dramatically. I would like to hire someone who can modify the CFD code using a "User Defined Function" which will uniformly remove mass from the chamber as a function of time, at a prescribed rate, without physically modeling an orifice to the atmosphere. Please contact me for details.
Category: Mechanical       
Skills: Computational Fluid Dynamics (CFD)       

M****son
 [?]
Sign in to view client's details.
| M****son
|    United States
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: 23h, 39m ago  |  Ends: 14d, 0h  |   15 Proposals
Working on an industrial design prototype that requires knowledge of basic mechanical movements, solar energy and motor specifications. Open to discussing project rate/ hourly rate ...as well as possible business collaboration for this well received concept with excellent opportunity for mass market appeal and huge profits. Please be willing to sign a Non disclosure agreement.
Category: Mechanical       

j****316
 [?]
Sign in to view client's details.
| j****316
|    United States
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: May 02, 2015  |  Ends: 12d, 23h  |   9 Proposals
Hello, I am interested in creating a sewing tool with special features. Please contact me where I can enumerate on it's functions further. Thank You!
Category: Mechanical       

a****187
 [?]
Sign in to view client's details.
| a****187
|    United States
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: May 01, 2015  |  Ends: 12d, 8h  |   3 Proposals
I will need a set of 4 acrylic glass sheets (2 are identical) ? 1 Front part ? 2 Left and Right part ? 1 Upper part I need 100 sets. Material : Clear Acrylic Glass 3.2mm (1/8 ") The edge/sides need to be clear polished (No burr, no chips). Laser cutting prefered. Clear plastic protection film on both sides Please refer to attached drawing. Your quote by Monday 5/4 EOB will be greatly appreciated. Please include your lead time in the quote. Parts are to be shipped in California USA. Please indicate the packaging and shipping cost. Thank you. Serge
Category: Mechanical       

d****eip
 [?]
Sign in to view client's details.
| d****eip
|    United States
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: May 01, 2015  |  Ends: 12d, 7h  |   0 Proposals
You are a structural engineer and either a licensed PE or able to be licensed in your state. You have experience in Telecommunications engineering including and not limited to structural analysis of towers, Rev G, Tower modifications and use of CAD/CAM tools for the creation of drawings. Must have at least 5 years experience with structural analysis of cell towers Must have excellent interpersonal skills. Must be able to do site and field visits and able to travel throughout the US as needed for field measurements, surveys etc.
Category: Civil & Structural       

w****eaf
 [?]
Sign in to view client's details.
| w****eaf
|    United States
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: May 01, 2015  |  Ends: 12d, 6h  |   1 Proposal
The Project Engineer/Manager is responsible for coordination of all tower deployment, trades, materials and execution of the project plan. Prior experience and knowledge of deployment on cell towers and in particular MW backhaul required. Should have a solid foundation in Engineering Principals, use of MS Project, Excel and able to review site drawings, engineering reports and interface with client executives. 5 years minimum deployment experience Excellent Engineering skills - RF/Electrical or PE Spanish and Portuguese desired Must be fluent in English as well Work is in US and LATAM
Category: Civil & Structural       

w****eaf
 [?]
Sign in to view client's details.
| w****eaf
|    United States
Fixed Price: Not Sure   |  Posted: May 01, 2015  |  Ends: 12d, 0h  |   10 Proposals
I have an idea for a medical scar product. I would like an engineer to work with me to handle the technical aspects. This project will address feasibility and design. Please contact me by PMB if you have any questions.
Category: Mechanical       

d****aik
 [?]
Sign in to view client's details.
| d****aik
|    United States
Hourly Rate: Not Sure   |  Duration: 1-2 weeks  |  Posted: Apr 30, 2015  |  Ends: 11d, 4h  |   23 Proposals
I am building a test stand for a client. I need an industrial designer / mechanical designer that has experience with pneumatics. I will be spec'ing out the cylinders, valves, and other important info and I need the designer to build the test stand based on other important info that I provide. I am fine with your choice of most popular 3D modeling CAD programs that are out there (let me know what you have) as I would want the parts and assemblies STEP, ACIS, or other out to myself. I expect a full set of drawings so that I can hand over to the machinist. I use FESTO and SMC products so that any files you will need can be easily downloaded.
Category: Mechanical       

C****WL0
 [?]
Sign in to view client's details.
| C****WL0
|    Canada
Hourly Rate: $20 - $30 / hr   |  Duration: 1-2 weeks  |  Posted: Apr 30, 2015  |  Ends: 11d, 2h  |   9 Proposals
The most urgent need is the wall and over 6 or 7 requires engineered plan in Tucson, AZ. I need a engineered plan for a concrete block (8x8x16 probably) in a residential setting. I need to talk to an expert about what I'm getting into going 6,7,8,10' tall and different options like the first 6' block with an iron bar extension on top. I just don't know what makes sense and what doesn't. Very important to me that the foundation doesn't crack the wall so I assume a soil survey will be needed. Also need foundation plans for a 30x30 residential addition 2 stories tall. I was planning on stick building, but I could see going CMU. I may or may not commission this plan at the same time, but I want to move on the wall.
Category: Civil & Structural       
Skills: Structural Engineering       

m****ell
 [?]
Sign in to view client's details.
| m****ell
|    United States
Fixed Price: Less than $500   |  Posted: Apr 30, 2015  |  Ends: 10d, 20h  |   5 Proposals
I need someone who is specialist in mechanical engineering ( composite materials and fracture mechanics ) and also has got knowledge in extended finite element method. I have conference paper written in 12 pages, and I need it to be reduced and limited to 6 pages. and I need the work to be done ASAP. any one not experts in composite materials and XFEM, please do not make bid. Thanks
Category: Mechanical       

A****ker
 [?]
Sign in to view client's details.
| A****ker
|    Australia
Fixed Price: Not Sure   |  Posted: Apr 29, 2015  |  Ends: 10d, 10h  |   4 Proposals
At least 4-axis parts with diameter up to 500 mm, length up to 3 meters epoxy rezin fiberglass, carbon fiber, aramid
Category: Mechanical       

i****t31
 [?]
Sign in to view client's details.
| i****t31
|    Russia
Hourly Rate: Not Sure   |  Duration: 3-4 weeks  |  Posted: Apr 29, 2015  |  Ends: 10d, 1h  |   3 Proposals
I need someone to help design how to make a large animatronic animal appear to walk and talk. There are at least 10 leg joints that need to be controlled however, there is a wheeled base between the legs that actually propels the animal. The leg movement (speed) just needs to match the speed of the base. There are also some motors in the head for mouth and ear movement. The mouth needs to be somewhat synced with a prerecorded audio routine (animal talking). The animal is in Philadelphia so it would be best to hire someone in that general area. Thx.
Category: Mechanical       

A****mes
 [?]
Sign in to view client's details.
| A****mes
|    United States
Fixed Price: Less than $500   |  Posted: Apr 28, 2015  |  Ends: 24d, 12h  |   14 Proposals
We are seeking an engineer to fill in on this project and future projects, when we are at capacity. We design wood framed custom residential and additions. In order to be considered you will need to have a structural engineering degree and strong wood design experience. Ability to draft structural plans in AutoCAD is a plus.
Category: Civil & Structural       

l****t23
 [?]
Sign in to view client's details.
| l****t23
|    United States
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: Apr 28, 2015  |  Ends: 1d, 9h  |   3 Proposals
Prior to commencement of building work,we need to get a copy of the Foundation design, certified by a registered engineer (RPEQ) for the design shown on the proposed plans. NOTE: This will also be required for the BOS. Can you please give us a quotation for this job. If you have any question,please do not hesitate to ask.
Category: Civil & Structural       
Skills: Structural Engineering       
Preferred Location: Australia

e****six
 [?]
Sign in to view client's details.
| e****six
|    Australia
Hourly Rate: $10 - $15 / hr   |  Duration: 1-2 weeks  |  Posted: Apr 28, 2015  |  Ends: 9d, 8h  |   33 Proposals
I am looking for an individual who can reverse engineering mounting brackets for our line of LED auxiliary lights. We have our own avenues for manufacturing, I simply needs mounts designed in SolidWorks and the necessary files for manufacturing.
Category: Mechanical       

B****ENT
 [?]
Sign in to view client's details.
| B****ENT
|    United States
Fixed Price: Less than $500   |  Posted: Apr 28, 2015  |  Ends: 9d, 4h  |   0 Proposals
Information app for every car model (nearly every car) Year made needed Model needed Price needed and other information needed 3-d picture needed
Category: Mechanical       

H****j13
 [?]
Sign in to view client's details.
| H****j13
|    United Kingdom
Fixed Price: $75 or less   |  Posted: Apr 28, 2015  |  Ends: 9d, 2h  |   11 Proposals
We need a logo development with the following characteristics: The name: Stellar Airpark plus a graphic addition to represent: - aviation - aircraft - aircraft taking off or landing - flying community Stellar Airpark is a flying community where every house has a hangar and there is a runway all share. The community is based in Arizona and has a variety of aircrafts based here. The logo we use is very dated and we are looking for a new modern logo which resinates with dynamic, young and seasoned pilots.
Category: Civil & Structural       

g****w02
 [?]
Sign in to view client's details.
| g****w02 *
|    United States
Fixed Price: Less than $500   |  Posted: Apr 28, 2015  |  Ends: 9d, 1h  |   16 Proposals
Hello Applicant! Currently we are looking for a drafter that can: - Take our scans of surveys and turn them into workable drawings/projects - Knows how to use or is willing to learn Microsoft Visio. (Not Auto-CAD) - Add details to drawings as instructed. What would you be doing? - Redrawing survey - add our construction plans (see video) - Add what people next door have (you have to use Google earth, very easy to use and figure out, I would explain it to you if we decide to use you) - Possibly help with the Cross view (See video, I have not decided If I am going to contract out this part of the project) Here is the video that should answer all your questions:   [obscured]  /t/0RVVtLtePv Who is our ideal person? Someone who is willing to work with us on a project to project basics. We have some very busy months and slow months. During busy months you would almost like a full time worker, but during slower months we would still have you draft all of our projects. What d...
Category: Civil & Structural       

s****101
 [?]
Sign in to view client's details.
| s****101
|    United States
Fixed Price: Not Sure   |  Posted: Apr 28, 2015  |  Ends: 9d, 0h  |   1 Proposal
Translating international filed patent from Japanese to English. Will require to sign a nondisclosure agreement prior to work. 70 pages but mostly in sketches.
Category: Mechanical       
Preferred Location: United States

J****ang
 [?]
Sign in to view client's details.
| J****ang
|    United States
Fixed Price: $50 - $100   |  Posted: Apr 28, 2015  |  Ends: 8d, 22h  |   16 Proposals
Im looking for a mechanical engineer to design 2d and 3d mechanical ventilation louvres for a greenhouse cooking facilities building including a detailed 1:5 section drawing and maybe an animated version on how it works during the process... More info coming soon....
Category: Mechanical       

M****iah
 [?]
Sign in to view client's details.
| M****iah
|    United Kingdom
Symbol Key
Payment method not yet verified
Payment verified
Purchased $1-$500
Purchased $500-$5,000
Purchased more than $5,000
You have already submitted a
proposal to this job