Save this Search
     
Sort by:
  • Posted Date
Engineering & Manufacturing
Hourly Rate: Not Sure   |  Duration: 1-2 weeks  |  Posted: 55 minutes ago  |  Ends: 14d, 23h  |   0 Proposals
The job is a feasibility study. I need someone with very good experience in FPGA design based projects. Our project would require: _ passively cooled FPGA and board. _ an FPGA able to implement: _______ at least 6 PCI Express 3 controllers or _______ 6 10 gigabit ethernet controllers (1Gbit is also enough) _______ if more even better _ it should have a CPU integrated (preferably ARM) or be able to configure one using a soft core. the cpu could be also as a separate chip on the board. In this case the FPGA must be able to share data with the CPU either via shared memory or other concept. _ the board with the required components should be below 300 dollars if possible in large quantities. We also need some advice on possible ways to update the FPGA configuration. We would prefer to do it without powering down the device.
Category: Product Design       

s****mod
 [?]
Sign in to view client's details.
| s****mod
|    Switzerland
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: 2h, 34m ago  |  Ends: 59d, 21h  |   7 Proposals
Hi, I am seeking someone who has experience in electrical engineering. The work requirements will be sent. Thank you.
Category: Electrical       

d****zzt
 [?]
Sign in to view client's details.
| d****zzt
|    Israel
Fixed Price: Less than $500   |  Posted: 7h, 28m ago  |  Ends: 14d, 16h  |   2 Proposals
Looking for someone to make me a 2.1 channel Class D amplifier board with passcode protected bluetooth. The amplifier has to run on 12v 1a and have approximately 2X25 watt fullrange output and 1X50 watt bass output.
Category: Electrical       

k****015
 [?]
Sign in to view client's details.
| k****015
|    Canada
Hourly Rate: $20 - $30 / hr   |  Duration: 3-4 weeks  |  Posted: 10h, 22m ago  |  Ends: 14d, 13h  |   13 Proposals
I need a custom board designed for the Atmel SAMA5D4 that should be relatively straight forward. I would like for the design to be done in Eagle, but that isn't a firm requirement. The board will have these types of components: 1) LCD connector for a 720p display 2) 256 or 512 MB of DDR memory 3) NAND flash (for the boot loader, firmware, etc.) 4) SD Card for the OS, etc. 5) Various regulators and filters 6) A few I2C/SPI/UART sensors 7) One or two debug connectors I have a good idea of what I need and this project needs to be done fairly quickly.
Category: Electrical       

b****ank
 [?]
Sign in to view client's details.
| b****ank
|    United States
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: 10h, 48m ago  |  Ends: 14d, 13h  |   10 Proposals
Looking for a 12V DC motor control for a small 100W motor. Need a CPLD with LCD or LED Display The Display can indicate 2 Digit Count that shows time that allows motor to run for a specified time. Say Display =01 implies 15 seconds Display = 02 implies 30 seconds etc., Need a up count button and down count button to chose the correct value. Components needed : 1. Small 2 digit LED/LCD Display, 2. 100W DC motor, 3.110V to 12V Power Adapter, 4. Up button (can be simple push button) 5. Down button 6. CPLD You can breadboard it and I will get a PCB designed once the system is working. Get back to me for more specific details
Category: Electrical       

s****539
 [?]
Sign in to view client's details.
| s****539
|    United States
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: 22h, 54m ago  |  Ends: 14d, 1h  |   1 Proposal
Taverna a Mediterranean food company based in Europe is looking for a Food Technologist that will come to our factory in Varel in Germany once a month for monthly analysis. We are looking for individuals that are from Varel or from the area.
Category: Product Design       

t****mil
 [?]
Sign in to view client's details.
| t****mil
|    Israel
Fixed Price: $1,000 - $5,000   |  Posted: May 03, 2015  |  Ends: 28d, 22h  |   8 Proposals
This job is for someone who can make a 3D powder printer (powder bed and inkjet head 3D printer) based on the open source 'Plan B' printer:   [obscured]  /plan-b/ You take care of the entire process, from analyzing the design, sourcing the parts, making the printer and eventually shipping the printer to Belgium. You should have some experience in this field. It's a very hands-on job that requires quite some technical skill. I'd like a few alterations to the original design we can discuss later (in brief, I'd prefer a RVS frame instead of aluminum and an other type of cartridge might be preferable). Feel free to discuss anything about this job with me first.
Category: Other - Engineering &...       

F****s78
 [?]
Sign in to view client's details.
| F****s78
|    Belgium
Fixed Price: Less than $500   |  Posted: May 03, 2015  |  Ends: 13d, 21h  |   2 Proposals
We are a gymnastics club that runs a turn up and play session. We currently use an app called 'sign in' and this asks each customer to sign in their name, mobile and email. It also totals up how many people have signed in - therefore who is on site each day. We can also then download this information as a CSV.. Most importantly for our members this app remembers them! As they hate to constantly type in email and mobile number - especially if they are regulars to our gym. As soon as they put their name in - it remembers all of their information! Unfortunately the app is being updated and the makers have said they cannot carry over old information to the new update! I will have very annoyed customers as I have over 1000 details already stored. Other reasons - being I would like a more personalized sign in app to our gym club - that could potentially add more features along the way etc. Most importantly I need our current information to be able to continue as normal in the new a...
Category: Product Design       
Skills: Electronic Design, Product Design       

s****oad
 [?]
Sign in to view client's details.
| s****oad
|    United Kingdom
Fixed Price: $500 - $1,000   |  Posted: May 03, 2015  |  Ends: 13d, 20h  |   0 Proposals
hello i need a fm transmitter which can send signal to a computer application . for example : if i am 2 km away from my computer and my computer is connected to a fm receiver and i have a fm transmitter through which i can send signals to the fm receiver and my computer will do a predefined action on a particular signal, Like YES on 1 type of signal and NO on other type of signal. we can hire a software developer for software part. the signal must be very fast as need lowest latency in transforming signals... if you can suggest any other device which is very small we can also use that like RF control. we can also use DTMF tones on phones ( but i have checked earlier there is a delay in DTMF tones). our main aim is to send some signals to our computer application which will react on out sent signals...... thanks
Category: Product Design       
Skills: Electrical Engineering, Electronics       

g****993
 [?]
Sign in to view client's details.
| g****993
|    India
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: May 03, 2015  |  Ends: 13d, 18h  |   4 Proposals
Hello, We are developing a Embedded system and we have to do Video broadcasting over WiFi and GPRS. If anyone have Expertise in either Hardware Part or Software Part , Pl contact Asap. Thanks & Regards : Amit Malviya
Category: Product Design       
Skills: Electronics, PCB Design, Wi-Fi, Bluetooth       

s****ics
 [?]
Sign in to view client's details.
| s****ics
|    India
Fixed Price: Less than $500   |  Posted: May 02, 2015  |  Ends: 13d, 12h  |   10 Proposals
We have a signal light tower, model ME-A, that needs to be connected to an integrated circuit wafer processing machine. There are three lights: red, amber, and green. See the first attached image. The second attached image has details on the required electrical connections. We need to turn the lights on and off from a computer. The computer interface is an Adlink 7442 PCI card with isolated digital outputs. See the attached data sheet. We should be able to attach three signal lines and a ground line from the 7442 to one side of the Light Control Circuit board, and the red, orange, green, and yellow wires from the light tower to the other side of the Circuit board. There should also be provision for 24V power. Given the schematic and part numbers, we can probably build it ourselves, but preference will be given to proposals that include fabrication and delivery of three circuit boards. I use the phrase "circuit board" loosely. It doesn't have to be a printed circuit...
Category: Electrical       

q****dex
 [?]
Sign in to view client's details.
| q****dex
|    United States
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: May 02, 2015  |  Ends: 13d, 12h  |   11 Proposals
Design or source and assist in manufacturing a MR16 LED driver that is capable of powering a 10 watt LED from major manufacturers including Phillips, Sorra, and TCP. Driver MUST be dimmable down to 5% (preferably 1%) with either forward or reverse phase (leading edge or trailing edge) triac dimming, preferably both. High efficiency electronic driver is preferred. Project phases include design or sourcing of driver and housing, building driver and housing prototype, testing, and assist in manufacturing. Final driver must be ETL of UL certified.
Category: Electrical       

j****738
 [?]
Sign in to view client's details.
| j****738
|    United States
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: May 02, 2015  |  Ends: 28d, 7h  |   17 Proposals
Design a PCB based on a prototype made with Arduino Mega. I have all boards and components schematics used in the construction of the prototype. Also within the design work, is to search components that have the same functionality but to lower the cost of the final product. ------------------------------------------------------------------------------------------ Diseñar una placa PCB en base a un prototipo hecho con un Arduino Mega. Tengo los esquemáticos de todas las placas y componentes que se utilizaron en la construcción de este prototipo. También dentro del trabajo de diseño, es buscar componentes que tengan las mismas funcionalidades pero que bajen el costo del producto final.
Category: Electrical       
Skills: Electrical Engineering, Electronics       

r****ell
 [?]
Sign in to view client's details.
| r****ell
|    Chile
Fixed Price: Not Sure   |  Posted: May 02, 2015  |  Ends: 13d, 4h  |   8 Proposals
I want to build a logo for my company dealing with the construction of wooden houses , laminated wood windows with double glazing, doors and others wood products. My company name is Danea Forest Grup.
Category: Other - Engineering &...       

L****tzu
 [?]
Sign in to view client's details.
| L****tzu
|    Romania
Fixed Price: Less than $500   |  Posted: May 02, 2015  |  Ends: 12d, 21h  |   0 Proposals
1.) Design the cell assigned to you with the following specifications using a layout editor(magic, etc..) a.) 0.5 Micron technology b.) Layouts fit in a 20 micron by 40 micron box c.) Balanced rise and fall delays 2.)Extract the circuit netlist for your cell and run SPICE simulations to study your cell performance 3.) Write a complete VHDL model for the cell using obtained values from the SPICE simulations 4.)Simulate your cell model (ModelsSim) and show in circuit results in comparison to circuit ( SPICE simulations) Expression:- Not((a+b)(c+d))
Category: Electrical       

l****eja
 [?]
Sign in to view client's details.
| l****eja
|    India
Fixed Price: Less than $500   |  Posted: May 01, 2015  |  Ends: 12d, 10h  |   19 Proposals
I have a rough draft of a 3d model of a speakerphone-type device prototype. See attached renderings. I would like to hire someone with industrial and manufacturing design knowledge who can create a unique and attractive new design - a design that will look appealing enough that a potential user would want to purchase it and place it on their table, countertop or desk. I would like the provider to have experience in product design of consumer electronics. This job is to create the exterior design as well as the design the interior (circuit board mounts, button supports - will provide measurements for circuit boards) - ready for 3d printing and injection molding. I would like to see 2 or 3 rough drafts/sketches of design ideas before we select one to do the final works. Deliverable would include 3d source files, 3d printing files and an internal/external rendering. I do have the original source files created from Blender if required. Please provide other product design samples...
Category: 3D Modelling       

l****abs
 [?]
Sign in to view client's details.
| l****abs
|    United States
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: May 01, 2015  |  Ends: 12d, 7h  |   6 Proposals
Verify and validate SDR development process and steps including FPGA coding, lab and field test results and analysis, long duration link test studies analysis. Work on assigned work such as telecom cabinet layouts/schematics/load calculations. Work on validation of path propagation analysis, RF performance (BER, Reliability, latency, throughput etc. Perform modeling via Excel, Matlab, Pathloss and other tools.
Category: Other - Engineering &...       

w****eaf
 [?]
Sign in to view client's details.
| w****eaf
|    United States
Hourly Rate: Not Sure   |  Duration: 1-3 months  |  Posted: May 01, 2015  |  Ends: 12d, 1h  |   6 Proposals
Need a circuit than can track a pencil or similar type line as a device moves along it and sends signals to two or four stepper/servo motors or other position controllers to keep the device in line by compensating for any drift within 6 mm (or more). The device consists of an inner and outer frame. The outer frame is for large movement. The inner frame is for precision movement. The outer frame moves horizontally, parallel to the line and is not electronically controlled. The inner frame holds the tracking unit. It is the tracking unit that adjusts while the outer frame is moving. If the outer frame begins to move out of the range of the inner tracking unit, an indicator comes on indicating the direction to move the outer range otherwise the inner frame adjusts automatically to maintain position. The inner unit can move via the servo motors or similar position controllers +/- 3 mm. This is the minimum acceptable range. Greater range is desired. Summary: Device tracks along a line Co...
Category: Electrical       

J****BUS
 [?]
Sign in to view client's details.
| J****BUS
|    United States
Hourly Rate: $15 - $20 / hr   |  Duration: Not Sure  |  Posted: May 01, 2015  |  Ends: 12d, 1h  |   6 Proposals
We are looking for a prototype biometric fingerprint time attendance system with proximity sensor to detect movement for power save mode, built in camera, GPRS/3G, GPS, WiFi and Touchscreen LCD for menu, keyboard/keypad and display options. The software needs to be configurable to push out data to our web based timesheets system alternatively a variant of android so we can build our own apps to run. A custom board or arduino/rasperryPI can be used for the prototype. As this is at prototype stage we are looking for suggestions to assist us develop this into a market ready product. More info is available on request.
Category: Other - Engineering &...       

m****olo
 [?]
Sign in to view client's details.
| m****olo
|    United Kingdom
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: May 01, 2015  |  Ends: 12d, 0h  |   4 Proposals
We are looking for an engineer who can design to our technical requirements a custom avionic panel (backlit panel to be machined out of aluminum or acrylic) and with a custom designed electronic circuit board. The electronic board will interface with our hardware controller for flight simulation. Our ideal engineer(s) must have: - Experience in designing enclosures - 3D models in Solidworks - PCB design - Arduino programming - Teensy USB development board programming - XPlane Flight Simulation (optional)
Category: Product Design       
Preferred Location: Canada

N****vio
 [?]
Sign in to view client's details.
| N****vio
|    Canada
Fixed Price: $500 - $1,000   |  Posted: May 01, 2015  |  Ends: 11d, 23h  |   1 Proposal
hello i need a fm transmitter which can send signal to a computer application . for example : if i am 2 km away from my computer and my computer is connected to a fm receiver and i have a fm transmitter through which i can send signals to the fm receiver and my computer will do a predefined action on a particular signal, Like YES on 1 type of signal and NO on other type of signal. we can hire a software developer for software part. the signal must be very fast as need lowest latency in transforming signals... if you can suggest any other device which is very small we can also use that like RF control. we can also use DTMF tones on phones ( but i have checked earlier there is a delay in DTMF tones). our main aim is to send some signals to our computer application which will react on out sent signals...... thanks
Category: Product Design       
Skills: Electrical Engineering, Electronics       

g****993
 [?]
Sign in to view client's details.
| g****993
|    India
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: Apr 30, 2015  |  Ends: 11d, 14h  |   5 Proposals
Experience with Com Lines and sensors. PCB Board Design/Firmware/software. Procurement. Will go into further detail with right candidate.
Category: Electrical       
Preferred Location: United States

m****gle
 [?]
Sign in to view client's details.
| m****gle
|    United States
Symbol Key
Payment method not yet verified
Payment verified
Purchased $1-$500
Purchased $500-$5,000
Purchased more than $5,000
You have already submitted a
proposal to this job