Save this Search
     
Sort by:
  • Posted Date
Posted: Within 24 hours
Fixed Price: $500 - $1,000   |  Posted: 43 minutes ago  |  Ends: 14d, 23h  |   0 Proposals
I want to manufacture a new archetype for a clock, where it is a 24 hour clock that rotates. So I would like the whole clock assembled 3d printed with the mechanics and electronics inside.
Category: 3D Modelling       

a****oit
 [?]
Sign in to view client's details.
| a****oit
|    United Kingdom
Fixed Price: Not Sure   |  Posted: 3h, 6m ago  |  Ends: 14d, 20h  |   1 Proposal
Please refer attached. Input voltage 48Vdc and generate 3 phase current output on 50Hz. 200VA and peak voltage shall refer at below.
Category: Other - Engineering &...       

d****ons
 [?]
Sign in to view client's details.
| d****ons
|    Malaysia
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: 3h, 55m ago  |  Ends: 14d, 20h  |   5 Proposals
Hi, Your profile is pretty interesting. I am from India and looking for someone to help me (off course for a remuneration ;-)) to build a prototype whose objective is to identify the object as soon as it enters a specific area or leaves defined area. I will not be able to put all details here. If interested, please contact me. Thanks
Category: Other - Engineering &...       
Skills: Electronics, PCB Design, 2089, HD RFID, Passive RFID       

d****une
 [?]
Sign in to view client's details.
| d****une
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: 6h, 48m ago  |  Ends: 14d, 17h  |   4 Proposals
This job is to design and lay out a pcb that will verify thermal performance of a design in progress. The pcb shape and chip locations of the current design are attached in a DXF. Your job is to place resistors in the locations of the chips so that the power draw is approximately correct. Please confirm your design package can open the DXF before bidding. This will be a 2 layer board. The load resistors will go on top with vias under them. There will be copper pours on the back. Chips 2, 6, 6b and 9 should all have pours between 1 and 1.5 square inches. Other pours should be 2 times the length and 2 times the width of the chip. Do not coat these thermal pours with soldermask. You can choose 1 board voltage (either 24V, 12V, or 5V). Power and ground will enter through pads on the edge of the pcb. Please include vias in these pads. Use resistors from Digikey that are in stock. Resistor loads should be within 10% of the values listed below. The units of the DXF are mils. There are some ...
Category: Electrical       

d****ius
 [?]
Sign in to view client's details.
| d****ius
|    United States
Fixed Price: Not Sure   |  Posted: 7h, 40m ago  |  Ends: 14d, 16h  |   7 Proposals
Hi we are in need of some one or a team of people to help build and design an amplifier. the project id to build a Bluetooth/ Wi-Fi speaker system. if you are interested in tacking on this job or have skills to suite this job please ask for more details thank you
Category: Electrical       

s****als
 [?]
Sign in to view client's details.
| s****als
|    Australia
Fixed Price: $500 - $1,000   |  Posted: 9h, 56m ago  |  Ends: 29d, 14h  |   9 Proposals
I need a device that is both GPS and Bluetooth capable that is able to connect with other devices of the same type (via Bluetooth). It has to be done quickly and display the distance between it and other devices (via GPS). I will disclose more details once we sign a non-disclosure agreement.
Category: Electrical       
Skills: Electrical Engineering, Electronics       

H****LLC
 [?]
Sign in to view client's details.
| H****LLC
|    United States
Fixed Price: $500 - $1,000   |  Posted: 10h, 14m ago  |  Ends: 14d, 13h  |   2 Proposals
Modeling and simulation for a large data set. Expert knowledge of aerospace engineering and concepts.
Category: Other - Engineering &...       
Skills: Electronics, MATLAB, aerospace, simulation       

m****nja
 [?]
Sign in to view client's details.
| m****nja
|    United States
Fixed Price: Not Sure   |  Posted: 11h, 38m ago  |  Ends: 14d, 12h  |   4 Proposals
Hi, We're looking for a sourcing agent who can find us *at least* 3 EPA regulated factories (Ideally, we want 5+) Plus, the factories should produce pest repellent devices that can be used indoor to repel pests.. If you can do this relatively small job, the pay will be one-time and it will be a few hundred bucks (depending on how well you do the work) You have to provide us the: #1 - Contact info/address of the factory in China and/or Taiwan. (Email/skype/address etc) #2 - Their EPA regulation certificate so we know (factually) that they have an EPA regulation. #3 - At least 3 different factories (ideally 5 or more. The more the better pay!) Thanks, - Ishan
Category: Other - Engineering &...       
Preferred Location: India/Southern Asia, Eastern Asia, Middle East & Central Asia

i****oni
 [?]
Sign in to view client's details.
| i****oni *
|    Canada
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: 11h, 41m ago  |  Ends: 14d, 12h  |   13 Proposals
I am looking for someone to create gerber files for a new project. I am needing a microUSB lion charger board similar to this:   [obscured]  /products/1944
Category: Electrical       

M****ets
 [?]
Sign in to view client's details.
| M****ets
|    United States
Fixed Price: Less than $500   |  Posted: 21h, 30m ago  |  Ends: 6d, 2h  |   36 Proposals
We need to modify electronic enclosure design. The enclosure is composed of two parts, front and back with hinge connecting them. We need to modify the dimensions as well the details inside and the hinge. We do have the original solidworks files if needed.
Category: Product Design       
Skills: AutoCAD, SolidWorks       

m****das
 [?]
Sign in to view client's details.
| m****das
|    Canada
Fixed Price: $500 - $1,000   |  Posted: 23h, 27m ago  |  Ends: 14d, 0h  |   2 Proposals
I have a custom headset idea, that would be for my personal use, and I would like to hire someone with the knowledge and ability to make it come to life.
Category: Electrical       

F****ios
 [?]
Sign in to view client's details.
| F****ios
|    United States
Symbol Key
Payment method not yet verified
Payment verified
Purchased $1-$500
Purchased $500-$5,000
Purchased more than $5,000
You have already submitted a
proposal to this job