Save this Search
     

All JobsPCB DesignHiring Open

 27 results  
Sort by:
  • Posted Date
Fixed Price: Less than $500   |  Posted: 5h, 30m ago  |  Ends: 14d, 18h  |   4 Proposals
This is a Very simple breakout board that connects a cc3000 wireless module to a teensey 3.0 microcontroller along with the necessary supporting hardware (level shifter, power regulator, etc) All component configurations are open source, and this should be very simple to build. Needed: PCB/Gerber layout/design given schematic/BOM (  [obscured]  /YXXWQ9) and my desired component layout arrange PCB manufacture of 100 boards arrange component assembly/population for 50 of the 100 boards
Category: Electrical       

f****ous
 [?]
Sign in to view client's details.
| f****ous
|    United States
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: Apr 18, 2014  |  Ends: 13d, 17h  |   19 Proposals
I have a PCB design using bluetooth created in Altium. I would like a second set of eyes to look over the design and make changes to improve it. NDA is needed.
Category: Electrical       

r****jam
 [?]
Sign in to view client's details.
| r****jam
|    United States
Fixed Price: $50 - $150   |  Posted: Apr 17, 2014  |  Ends: 13d, 7h  |   12 Proposals
I need someone that is experienced in Eagle CAD to make a change to an existing PCB. This change consists of hooking up three new low power MOSFETs, adding 0603 three resistors, and rewiring a couple of nets. I will provide both the eagle schematic and PCB, plus a pdf of the new schematic with the changes highlighted. If we are happy with the results, this will probably lead to future jobs too. I'm a circuit designer but I'm not very good with Eagle. So no circuit design experience needed, just lots of experience laying out printed circuit boards with Eagle CAD. Thanks.
Category: CAD       
Skills: OrCAD, Electronics, PCB Design       

J****lEE
 [?]
Sign in to view client's details.
| J****lEE
|    United States
Fixed Price: Less than $500   |  Posted: Apr 17, 2014  |  Ends: 13d, 5h  |   11 Proposals
Schematic capture and board layout for a tiny PCB board. The board is a very simple and has only 2 connectors: One is a dual stacked USB 3.0 R/A SMT connector and the second is a 19 pin header to plug to USB a 19 pin header dual USB 3.0 port on MB. They are a high speed signals, so consideration of signals interfaces must take into board layout.
Category: Other - Engineering &...       
Skills: PCB Design       

e****avi
 [?]
Sign in to view client's details.
| e****avi
|    United States
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: Apr 16, 2014  |  Ends: 12d, 4h  |   4 Proposals
We need an interface cable designed and prototyped that will incorporate three channels of charge mode amplifiers with gain and a single channel 15W speaker amplifier. This cable will connect a device containing two piezoelectric sensors and one speaker to an existing embedded system. Currently, the embedded system connects to a slightly different device which contains a speaker and two microphones. The goal is to include the electronics in the prototype cable that will interface the new device to the existing embedded system. We would like this designed and fabricated ASAP and would like five cables made after we have tested the prototype. A non-disclosure agreement will be required to work on this project. See attachment for the requirements. Applicants should be well versed in analog circuit design and PCB layout.
Category: Electrical       
Preferred Location: United States

j****007
 [?]
Sign in to view client's details.
| j****007
|    United States
Fixed Price: Not Sure   |  Posted: Apr 16, 2014  |  Ends: 11d, 20h  |   21 Proposals
Looking for an experienced CAD designer with good links to rapid prototyping facilities Project is to design a plastic case for a new educational computer for teaching programming and controlling electronic projects We need a design that is simple, functional and low cost.- the design will be used in an educational setting : - Will need to be capable of assembly with simple tools as a sales option is a kit of parts - Some electronic integration experience needed (e.g. USB sockets, low voltage wiring, PCB mounting) including ability to incorporate CE and FCC requirements into the design - Case will need to include some small projections functionally similar to those for a popular brick-based childrens toy - Deliverables will include CAD files suitable for manufacture (in a popular format), 3D render images and at least one physical prototype (either produced by you or via your contacts) - Prototype shall be a high quality, functional item conforming to the design with smooth edges ca...
Category: Product Design       

i****ps2
 [?]
Sign in to view client's details.
| i****ps2
|    United Kingdom
Fixed Price: $1,000 - $5,000   |  Posted: Apr 14, 2014  |  Ends: 10d, 11h  |   6 Proposals
We are looking for someone to design a mobile device that can record 4 1080p cameras 100% synchronized. We are looking for circuit / PCB design and consulting. This is a mobile device that is not battery powered.
Category: Product Design       

p****ris
 [?]
Sign in to view client's details.
| p****ris
|    United States
Fixed Price: $1,000 - $8,000   |  Posted: Apr 13, 2014  |  Ends: 35d, 5h  |   8 Proposals
4-5 week design cycle. Extremely reliable. Fail safe. Size, weight, power should be minimized. Vibration resilient. EMI resilient MIL-STD-464. Design PCB and required firmware/software to convert about 12 0-5 volt analog inputs and about 12 thermister inputs to a canbus or rs-232/ttl level output. Canbus preferred. 10 bit or greater, data rate should be 1hz or greater. The number of inputs can be negotiable (for example if your microcontroller can only do 16 I/O). A second section of the board(s) should interface with two Novatel OEM615 GPS boards to provide conditioned power (I believe 12VDC and 3.3VDC), 232/LVL conversion, and mechanical attachment of GPS boards. OEM615 boards require the two voltages, two traces between the two for comms, and a level converter for one of the boards (they communicate on TTL and we need 232). This new PCB will essentially be a motherboard. +12 volt DC input (PCB must condition as required) Temp rating: -26F to 160F operational, -50F to 160F storage...
Category: Electrical       
Preferred Location: United States

g****red
 [?]
Sign in to view client's details.
| g****red
|    United States
Fixed Price: $1,000 - $5,000   |  Posted: Apr 12, 2014  |  Ends: 8d, 5h  |   11 Proposals
I work for Kimberlight LLC, a start-up company based out of Safford, AZ. My team is actively developing a sports oriented talking toy with the following features: - traditional push button capability (2 controllers) - 5 to 10 minute internal sound file storage capacity - wireless activation of sound files (bluetooth or RF) - ability for sound files to be updated (user can download and replace locally) - rechargeable battery (USB based) - embedded speaker We would be interested in speaker with your team in greater detail about our project and your organizations ability to help. Specifically we would want the following services rendered: - source code - Gerber file of PCB / electronics layout - working prototype of the design Prior to discussing specific details we would want a signed non-disclosure agreement. Thanks - Brian Lamanna
Category: Product Design       

l****557
 [?]
Sign in to view client's details.
| l****557
|    United States
Hourly Rate: Not Sure   |  Duration: 1-2 weeks  |  Posted: Apr 10, 2014  |  Ends: 6d, 8h  |   9 Proposals
Hello, I am looking for someone to design the electrical components and circuitry for a wrist worn consumer electronic. The look and much of the industrial design is already done. I have a pretty solid idea of how the product should perform and much of the basic placements of the electrical components. This is a job that is under a VERY tight deadline. I need everything done in two weeks. What's involved: Firmware PCB design LiPo Power management Curved LED Array display General Circuit design Micro controllers
Category: Electrical       

k****ele
 [?]
Sign in to view client's details.
| k****ele
|    United States
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: Apr 10, 2014  |  Ends: 6d, 0h  |   4 Proposals
Hello, I was wondering if you could create an electronic device for me? Unfortunately my knowledge of electronics is somewhat limited however; I have taken a video of the device to show what I am after.   [obscured]  /watch?v=NJKehBVTD7s Some Info: The EMP uses 10 wraps on the large coil and 100 wraps on the small coil. It uses 6 x 3.7v lipo batteries. The pulse timing can be changed via a button on the side. I would like to be able to charge the batteries from a dc jack plug. I am interested in just the PCB and components (no coil, case or batteries). I am after about 20 making for now. Would something like this be possible to make? If a pre-set chip with timings is not do-able could an alternative like a potentiometer to control the pulse timings be created? Unfortunately, I don't have a device I can send you as it was broken when it was taken apart by another company. If it makes it any easier I can call you or contact you through Skype etc. Many thanks, Robert Hetheri...
Category: Electrical       

S****Rob
 [?]
Sign in to view client's details.
| S****Rob
|    United Kingdom
Hourly Rate: $10 - $15 / hr   |  Duration: 1-2 weeks  |  Posted: Apr 10, 2014  |  Ends: 6d, 0h  |   8 Proposals
Hi I need a Layout Engineer to layout a couple of boards in Allegro. The schematics are already done in Orcad.
Category: Electrical       

o****974
 [?]
Sign in to view client's details.
| o****974
|    Israel
Fixed Price: Less than $500   |  Posted: Apr 09, 2014  |  Ends: 5d, 13h  |   11 Proposals
I need some assistance with creating a custom pcb board for a small quadcopter. We are looking to integrate everything into one board. If you have experience with designing multicopters and autonomous systems we want to work together with you.
Category: Electrical       

t****t15
 [?]
Sign in to view client's details.
| t****t15
|    United States
Fixed Price: Not Sure   |  Posted: Apr 09, 2014  |  Ends: 5d, 9h  |   20 Proposals
UPDATE: April 11, 2014 We are going to postpone this project as it currently is (addition of a separate sensor PCB) as we test using a off the shelf sensor board. If this method works, then we will be going straight into the development of a redesign of both the module and additional sensor boards. This posting will stay open until it automatically closes. We won't be selecting a freelancer until after our testing. Thank you We have an RF transceiver Module used in a mesh network that does not require any external components to operate but we would like to add additional sensors to it. You can view the module here   [obscured]  /weben/index.php?sekce=products&id=tr-52d&ot=transceivers&ot2=tr-52d Any questions, just message me. Thanks Neil
Category: Electrical       

W****erd
 [?]
Sign in to view client's details.
| W****erd
|    Canada
Hourly Rate: $15 - $20 / hr   |  Duration: Not Sure  |  Posted: Apr 08, 2014  |  Ends: 78d, 21h  |   6 Proposals
Ayuda virtual con tu ordenador Ayuda para la electronica analogica y digital Creacion de pcb Ayuda con Software y hadware de ordenadores
Category: Virtual Assistant       

O****ATZ
 [?]
Sign in to view client's details.
| O****ATZ
|    Honduras
Hourly Rate: $10 - $15 / hr   |  Duration: 4-6 months  |  Posted: Apr 07, 2014  |  Ends: 3d, 8h  |   30 Proposals
Hey, We are looking for PCB CAD professional that has experience with PADS, Orcad and Altium. Designer needs to have a good background in PCB manufacturing and work within the limitation we provide based on the complexity of the board. Communication skill are critical as we are planning to co design the PCB. Quality and availability is big for us.
Category: CAD       
Skills: 3D Modeling, Altium Designer, AutoCAD       

z****nar
 [?]
Sign in to view client's details.
| z****nar
|    United States
Fixed Price: Not Sure   |  Posted: Apr 07, 2014  |  Ends: 3d, 1h  |   24 Proposals
Hello everyone, we need an expert in PCB design for the design of a fractional motor control board. 3" by 4". Frankly, not a difficult task for someone that knows what they are doing. Thank you! Nikoleta
Category: Electrical       
Preferred Location: North America

b****ana
 [?]
Sign in to view client's details.
| b****ana
|    United States
Fixed Price: Not Sure   |  Posted: Apr 07, 2014  |  Ends: 47d, 19h  |   16 Proposals
Hi there, we are new start-up company looking for a contractor to help us take care of several of the technical aspects of our first product. Our product will be an anti-theft, loss prevention and statistics tracking device for skiers and snowboarders. We require a contractor to oversee two aspects of the product and consult with us: 1. To design, produce and test the PCB for the device. 2. To oversee embedded programming that ensures a reliable connection to iPhone and Android smartphones via the new Bluetooth Low energy standard. The product description and the technical specifications have been attached. Skiing or snowboarding experience and passion on behalf of the team would be a great advantage. The project will be considered finished with a 6 functional prototypes which can connect to a smartphone app and be programmed. It will also include the hardware designs ready for mass production. Detailed lists of the tasks are given in the attachments. Please let us know if you ...
Category: Electrical       

s****az1
 [?]
Sign in to view client's details.
| s****az1
|    Australia
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: Apr 07, 2014  |  Ends: 2d, 18h  |   21 Proposals
I have an almost completed schematic for a simple electronic sensor containing an ARM M0 MCU/Transceiver (nRF51822), an accelerometer (MPU-6000), and a microSD flash card adapter, all operating on a LiPo cell. First I'd like an experienced EE to take a look at the schematic and help me transfer it to a PCB board (Gerber files) that I can send off to manufacturing and get a stencil for. Additionally, I could use some help troubleshooting the application that is to be loaded onto this PCB board, on top of the S110 Soft Device provided by Nordic. I'm looking to take DMP calibrated accelerometer and gyroscope data from the MPU-6000 and send it to the internal 1024 byte FIFO buffer. When the buffer fills and sends an interrupt to the MCU, I want it to wake up and transfer the data collected to the microSD card. Additionally I want a button for power, and a button that when pressed reads the data written to the SD card since last time and sends it over bluetooth low energy to a phone (no...
Category: Electrical       

T****rAv
 [?]
Sign in to view client's details.
| T****rAv
|    United States
Hourly Rate: Not Sure   |  Duration: Not Sure  |  Posted: Apr 06, 2014  |  Ends: 2d, 11h  |   26 Proposals
we require on an ongoing basis the need to reverse engineer various small pcb boards. Most of them are 2 layer with basic components. You will need to be able to re-create the schematic drawings, gerber file, BOM and firmware. If you have skills in this area, the please respond so we can discuss in more detail.
Category: Electrical       

b****ces
 [?]
Sign in to view client's details.
| b****ces
|    Australia
Hourly Rate: $10 - $15 / hr   |  Duration: 1-2 weeks  |  Posted: Apr 04, 2014  |  Ends: 15d, 8h  |   20 Proposals
Seeking well qualified PCB designer who can will assist with new design Schematic, PCB design, BOM and Documentation. With previous working knowledge of: - Consumer Electronics Products - Medical Products - Altium
Category: Contract Manufacturing       
Preferred Location: North America, Eastern Asia, Middle East & Central Asia

d****n8a
 [?]
Sign in to view client's details.
| d****n8a
|    United States
Fixed Price: Less than $500   |  Posted: Apr 02, 2014  |  Ends: 72d, 18h  |   7 Proposals
We look for design dimension and simulation of 3D Antenna integrate in can case. The Antenna design has to be 50 ohm with small-sized and high-gained, see photo. The design has to maximizing the antenna power radiation for 2.4 Ghz to 2.5 Ghz range. The PCB is FR4 is: 1mm, dialectic is 4.4 and has GND layer. Since we design many sizes RF PCB for Bluetooth Low energy, will be following works base on this design, when the changing factor will be the PCB size. The height and the insertion point will be the same in most cases.
Category: Electrical       
Skills: Antenna, Antenna design, microwave       

b****ert
 [?]
Sign in to view client's details.
| b****ert
|    Israel
Fixed Price: Less than $500   |  Posted: Apr 02, 2014  |  Ends: 72d, 17h  |   4 Proposals
We look for design dimension and simulation of 3D Antenna integrate in can case. The Antenna design has to be 50 ohm with small-sized and high-gained, see photo. The design has to maximizing the antenna power radiation for 2.4 Ghz to 2.5 Ghz range. The PCB is FR4 is: 1mm, dialectic is 4.4 and has GND layer. Since we design many sizes RF PCB for Bluetooth Low energy, will be following works base on this design, when the changing factor will be the PCB size. The height and the insertion point will be the same in most cases. we need to see a a preview demo work before grant the the project.
Category: Electrical       

b****ert
 [?]
Sign in to view client's details.
| b****ert
|    Israel
Fixed Price: $200 - $600   |  Posted: Apr 01, 2014  |  Ends: 2d, 9h  |   24 Proposals
I have a board that was designed in 6 layers, using a blind via and very small trace paths, and as result has increased the production cost greatly. What I need is for someone to take the current design schematic, and either separate the design into two independent boards that interface with each other and mount within the same enclosure space, or fix the board so that it is not so closely to produce, meaning increase the trace or component issues. Because of time, I am in need of this fix quickly, in a matter of days not weeks, so that the board can be produced. So if you are selected for the project please do not agree to this unless you have the skillset to complete it within the timeframe required. This is not a, from the ground up project, as the PCB has already been designed. So the project requires the following just to recap: 1. Separate the existing PCB, (BRD file will be provided after award), into two boards one with 4 layers and another with 2 for example, that result...
Category: Electrical       

d****ard
 [?]
Sign in to view client's details.
| d****ard
Symbol Key
Payment method not yet verified
Payment verified
Purchased $1-$500
Purchased $500-$5,000
Purchased more than $5,000
You have already submitted a
proposal to this job