Save this Search
     
Sort by:
  • Posted Date
Fixed Price: Not Sure   |  Posted: Mar 27, 2015  |  Ends: 13d, 13h  |   9 Proposals
Hi, this project is about developing 3 micro circuits (1 of them is remote controller). I need developer to make the following microcircuit: 1) Micro circuit with LED lights strip (6 LEDs) remotely turned on and freezing for 8 seconds, and then self shutting down. size: 80x30x8mm max Working Voltage - 12V max 2) Micro circuit with LED lights strip (6 LEDs) remotely turned on and freezing for 8 seconds, and then self shutting down, size: 80x30x8mm max Working Voltage - 12V max 3) Micro remote control (not IR), it is desirable to radio waves (or Bluetooth). Which will operate at a distance of 10 meters (max). The purpose of the remote control is to switch on LED lights described above. So remote control will have only 2 buttons. size: 45x25x10mm. Working voltage - 3V max. Briefly, I need 2 separate devices, which controled by remote control (3rd device). Budget: TBD
Category: Electrical       
Preferred Location: North America

S****er8
 [?]
Sign in to view client's details.
| S****er8
|    United States
Fixed Price: $100 or less   |  Posted: Mar 24, 2015  |  Closed  |   14 Proposals
Double sided PCB 60x60mm from eagle .sch and .brd. It connects to Oled display and another circular board. Few constraints: 4 holes, 5 connectors, 4 buttons on the bottom,MicroUSB at 90degree facing front. 5th button can go anywhere.
Category: Electrical       

c****ort
 [?]
Sign in to view client's details.
| c****ort
|    United States
Fixed Price: Less than $500   |  Posted: Mar 23, 2015  |  Closed  |   6 Proposals
i need a small pic board with an ambient light sensor onboard. It will output PWM based on an internal programmable table it will run on 12 volts or 5 volts Vcc. it will be programmable through an I2C tool or onboard USB header. board should be about 1" x 1" with a single connector for normal operation and programming through a second conenctor. I need board layout, schematic, gerbers and programming tool. must use latesst version of software, must be available today.
Category: Electrical       

l****pro
 [?]
Sign in to view client's details.
| l****pro
|    United States
Fixed Price: $5,000 - $10,000   |  Posted: Mar 22, 2015  |  Ends: 8d, 3h  |   49 Proposals
Hi everybody. I need expert help in design electronic board. It consist of MCU (on your choise) that listens about 5 sensors (analog and digital) and controls about 5 devices (ON-OFF-PWM up to 60W) in accordance with the firmware logic. Also it must include DC-DC converter and status indication (with LEDs). Power supply from 12V DC. Board size 140x60x20 mm max. Also I need you to produce first sample board with factory quality (with mask and silk screen, mount components and test it. And also I need you to make firmware. As a result I want gerber files, project files, BOM, firmware source code and working sample device. Please offer tour terms and price.
Category: Electrical       

s****888
 [?]
Sign in to view client's details.
| s****888
|    Russia
Fixed Price: Less than $500   |  Posted: Mar 20, 2015  |  Ends: 5d, 21h  |   11 Proposals
Hi, I would like to hire someone to build a circuit board with electric shocking element. Please only countries that can safely ship this without risk of it being seized by customs! In the attached pictures, you will see what the final product should look like. The schematic shows the device I currently have. What you create will be identical except that it will probably not have a voltage regulator and it must also have a potentiometer. The shocking element will be at the end of wires attached to the PCB. There should be a potentiometer added to the circuit adjustable so that the shock is mildly painful at the highest setting and almost unnoticeable at the lowest. In the middle it should tingle just enough to wake someone up if they were sleeping. I do not know what voltage are necessary to do this, so you would have to experiment on yourself. The board should fit inside 2.3" x 3.7" and accommodate a 9V battery. If this is possible and you can do it, please message me...
Category: Electrical       

s****lig
 [?]
Sign in to view client's details.
| s****lig *
|    United States
Fixed Price: Less than $500   |  Posted: Mar 13, 2015  |  Closed  |   6 Proposals
This device shall be able to (1) detect if there is anything up to 1 meter above it in a 5 meter times 7 meter storage space in both day and night lighting condition (2) once it detects any object staying in the space for 10 secs, it sends out a signal to cloud sever (no wifi avaliable) including its assigned space # and a "occupied" signal (3) when the space is emptied, it can also detect it and send out a signal with space # and a "vacant" Working condition (1) must work in locations without Wifi but be able to send out signal (2) water-resistant (3) not crushed or broken by at least 200,000 Pa (3) using a single button battery with life expectation of 3 months or more Note: please use components that are currently available in the market place and include vendor & cost in your design ADD: you can use AT&T M2X for data communication
Category: Electrical       
Skills: Electrical Engineering, Electronics       

g****911
 [?]
Sign in to view client's details.
| g****911
|    United States
Fixed Price: Not Sure   |  Posted: Mar 13, 2015  |  Closed  |   11 Proposals
I need your help in desining electric device - frequency divider. On input 120Hz 5V strobes, on output 60Hz 12V 1A strobes. Power supply from 12V DC. As a result I want gerber files, BOM and produced board with fabric quality. Board size 40x40 mm. Waiting for your offers and price.
Category: Electrical       

i****v75
 [?]
Sign in to view client's details.
| i****v75
|    Russia
Fixed Price: Not Sure   |  Posted: Mar 11, 2015  |  Closed  |   8 Proposals
I have a schematic, but now the board needs to be designed. The board is 'sandwiched' between two other boards (a O-Droid C1 and a GPS receiver card), and provides some other interfacing (rs232 and rs485) and power to the other boards. I have an Eagle schematic with 3 x serial ics, 3-4 other ics, three headers and should fit into about 100mm x 100mm board. Okay to use 4-layer board. I have also defined some of the pcb pads, but these will need double-checking. There are a few other constraints, such as a cutout for an SMA RF connector. Attached is a pdf of the schematic, but all Eagle files and libraries can be supplied if required.
Category: Electrical       

j****_3d
 [?]
Sign in to view client's details.
| j****_3d
|    Australia
Fixed Price: $500 - $1,000   |  Posted: Mar 10, 2015  |  Closed  |   5 Proposals
Hi, I need to control a Canon DSLR camera via a raspberry pi. I know the system is currently being used by other people but want to build and develop my own. I will have a camera in a remote area and I need the following. The Pi to talk to the camera and control the cameras interface so we can change settings. For the Pi to be able to run programs that change the camera settings slowly, so at one point in time the cameras shutting speed is x and over 4 hours slowly changes to y. The Pi to receive the images from the camera and store them on a hard drive. The Pi to talk to a 3G modern and for me to remotely control the camera and view the latest images. The Pi to send the images over the 3G modem to my server. Help setting up the 3G modem, suggestion of what to buy and then setting it up. Suggesting what kit I need to buy as currently I own nothing apart from the camera.
Category: Electrical       
Preferred Location: United Kingdom

P****res
 [?]
Sign in to view client's details.
| P****res
|    United Kingdom
Fixed Price: Not Sure   |  Posted: Mar 07, 2015  |  Closed  |   13 Proposals
We are looking for an experienced Arduino developer to build a mock up application for usability study of a networking router. The screen layout has been designed and we want to develop a demo unit so that we could conduct usability study on the UI. A perfect candidate should possess at least two years experience in Arduino programming with at least completion of two successful Arduino projects. The user interface will be through a 128 x 64 dot matrix LCD screen and three buttons (Home, Up and Down). The developer shall be responsible to design the circuit and provide us the schematic, BOM and instructions to put together the system. The developer will program the system according to the screenshots. For those who are interested, please submit your CV. Once we have the NDA in place, We shall share with you the screen definition. You can submit the bid after review the specification. Here is the tentative timeline: March 9: Pick the winner March 13: Completion of the system ...
Category: Electrical       
Skills: C, C++, Arduino       

i****ear
 [?]
Sign in to view client's details.
| i****ear
|    United States
Fixed Price: Not Sure   |  Posted: Feb 26, 2015  |  Closed  |   15 Proposals
We have two components that need to be connected together with proper power and programming interfaces. The PCB needs to be no larger than 2in x 2in. Ideally we would like to have a PCB antenna (2.4Ghz ZigBee), but will settle for a chip antenna if it means space savings. The RFID antenna will need to be PCB. There also needs to be a connection for an RGB LED. ZigBee System-on-Chip: Atmel ATmega256RFR2 RFID: STMicroelectronics ST95HF Battery: two 1.5v AA alkaline LED: Generic RGB LED
Category: Electrical       
Skills: Electrical Engineering, Electronics       

****
 [?]
Sign in to view client's details.
| Client
|    United States
Fixed Price: Less than $500   |  Posted: Feb 25, 2015  |  Closed  |   40 Proposals
We need to have a PCB design modified. The board is double sided and is 38mm x 25mm and is low density. The PCB is for a wireless microphone, it is based off a DECT module and only needs about 15 lines run. Files are currently in Altium.
Category: Electrical       

l****ech
 [?]
Sign in to view client's details.
| l****ech
|    United States
Fixed Price: $500 - $1,000   |  Posted: Feb 19, 2015  |  Closed  |   1 Proposal
I am interested in designing, developing and manufacturing a RECEIPT size ONLY document scanner proto-type using off-the-shelf electrical and electronics components. Here is a brief functionality description: Upon sensing the paper in the feeder auto start the scan and store the file on SD card in JPG format. There is NO USB port required for file transfer. Only 2 ports required are: for charging the internal battery and the SD card slot. I am developing this proto-type for a project which will require 100 scanners. Upon project success many more scanners will be required. I need quotes for the design, development and delivery (California, USA) for 100 such scanners. If possible, do give quotes for 2-3 variations of the components / functionality. Contact me for any additional considerations needed for making scanner more efficient or cost lesser. Budget in the job description is indicative. The details specs are below. Paper sensor: mechanical or optical Auto launch / scan star...
Category: Electrical       

n****yaz
 [?]
Sign in to view client's details.
| n****yaz *
|    United States
Fixed Price: Not Sure   |  Posted: Feb 19, 2015  |  Closed  |   13 Proposals
I'm interested in creating circuit and PCB schematics for RS232 analyzer device. Main functional is to show RS232 sniffed data on LCD screen. Device should have two RS232 ports to be able sniffing data in both directions. LCD screen should have touch screen. Only one additional button will be used ? power button. Device should run on rechargeable batteries and be able to recharge from USB. I'll write program under Arduino IDE myself. I'm waiting to receive circuit and PCB schematics in one of the popular PCB design software (eg. Eagle). All electronic parts should be available from Europe supplier (eg. Farnell/Elfa/Rs-delivers). Most of the parameters could be changed up to your expertise. If you have experience with some similar component, please use it. I have no strict limit in time, but waiting for the price to be reasonable, since I'll use this device for my personal purposes. Parts description: - MCU - Atmel SAM3X8E ARM Cortex-M3 (I'll Arduino IDE for programming). Could be cha...
Category: Electrical       

****
 [?]
Sign in to view client's details.
| Client
|    Latvia
Fixed Price: Not Sure   |  Posted: Feb 18, 2015  |  Closed  |   2 Proposals
We are an architect and construction firm in need of a single project solution for a house currently in construction. We would like to have a series of 15 windows operate by two decision statements 1. Im in sunlight 2. It's more tolerate outside than inside (74 deg). I think this is a simple electronic engineering gig and it's ok if we use off the shelf kits. Motorizations is purchased and 110 v system. If this is in your wheelhouse please contact me. Thanks Cameron Crockett AIA 562.997.zero971. X1 or email Cameronatultra-unit.com
Category: Electrical       

C****ual
 [?]
Sign in to view client's details.
| C****ual
|    United States
Fixed Price: Not Sure   |  Posted: Feb 11, 2015  |  Closed  |   10 Proposals
This project is to design a high-efficiency, compact MPPT Charge Controller based on the attached IC (LT8490), to be used with the attached lithium-ion batteries. The batteries will be attached in a 4S configuration. Each battery is 4.2V, but the charge controller is to only charge them to 4.1V each, or 16.4V for the entire pack. They are to be charged with a CC/CV profile, as per their datasheet. (Configuration of IC on Pg 13 of 8490f.pdf) The charge controller should be optimized for 1-2A of incoming current at 24V, but the locations and parts that should be changed to increase this capacity should be clearly marked in additional schematics. Thermal considerations should be taken into account with component choices, and all possible components should be at least X5R or equivalent. A thermistor divider network should be in place for temperature compensation/shutdown of battery charging. If possible, enough thermistors should be allowed to monitor each battery on the TEMPSENSE pin ...
Category: Electrical       

T****unt
 [?]
Sign in to view client's details.
| T****unt
|    United States
Fixed Price: $500 - $1,000   |  Posted: Feb 11, 2015  |  Closed  |   18 Proposals
Hi, I am designing a device that will be attached the roof of a car and has the following components integrated on the device: - solar panel (maximum 12in x 12in) - small battery (for energy storage) - GPS - Accelerometer - Modem (that holds a GSM chip to transmit the signal) The plan for the device is to be stuck (via an adhesive) to the roof of a passenger vehicle. I am looking for a physical design of this device as well as an overview of the options and costs of the components. Thanks!
Category: Electrical       

c****t06
 [?]
Sign in to view client's details.
| c****t06
|    United States
Fixed Price: Less than $500   |  Posted: Feb 11, 2015  |  Closed  |   12 Proposals
We are looking for someone to design a 54Mhz antenna for RX only for a radio receiver. The channels are 12.5 kHz apart from 53 to 54.5Mhz. The receiver is only 100mm x 100mm x 100mm so we want an antenna which would suit the design. Any design will be considered whether PCB, loop, helical etc.
Category: Electrical       

m****een
 [?]
Sign in to view client's details.
| m****een
|    South Africa
Fixed Price: Not Sure   |  Posted: Feb 07, 2015  |  Closed  |   29 Proposals
Looking for someone who can do PCB layout for me, preferrably with orcad layout. I have all schematic ready, footprints/padstacks of components ready. Board will be approximately 3x3 inch. Half of the board is already laid out (due to existing reference design). There are about 50+ components to layout and about 10+ datasheets that have details of layout guidelines.
Category: Electrical       
Skills: OrCAD, PCB Design       

o****ngr
 [?]
Sign in to view client's details.
| o****ngr
|    United States
Fixed Price: Less than $500   |  Posted: Feb 05, 2015  |  Closed  |   5 Proposals
I am looking for a small All in One Bluetooth module with the following specifications 1. 4.0 / 4.1 LE 2. SPI Interface - 24Mbps or 16Mbps (Minimum 4Mbps) 3. All in One (Chip + Shielding + Antenna) 4. Weight: 1gram or close 5. Size: 15mm x 15mm or smaller 6. Range: 100m (preferrable), 20m (minimum) Looking for a Google Search or Digikey/Mouser search etc, to find a chip that meets the above requirements.
Category: Electrical       

j****tti
 [?]
Sign in to view client's details.
| j****tti
|    United States
Fixed Price: Not Sure   |  Posted: Feb 05, 2015  |  Closed  |   5 Proposals
Hi i am looking for someone who can design and made fully functional prototype of similar controller like you can see in the video. In the video controller can control 3 axis but i am looking for 4 axis controller via 2 joysticks. Controller can be base on Arduino, Raspberry Pi or on any other micro controller base board or you can build your own. Must have: Software 1. Timelapse menu 2. Video menu ( i already have controller for 2 axis with very good video and timelapse software. My system is running on Arduino. Most of the function i like and would like to have on the new system will be specified later) Hardware: 1. Fully populated PCB board or boards 2. All cable connection with motors and with the batteries must have secure connectors so the cables can't get loose. 3. 2x joysticks 4. Large LCD screen ( not sure if touch screen yet) 5. Wifi connection with all 4 axis 6. Wire connection with all 4 axis 7. 5V and up maybe 24V ? 8. If not touch screen is selected some kind o...
Category: Electrical       

e****365
 [?]
Sign in to view client's details.
| e****365
|    United States
Symbol Key
Payment method not yet verified
Payment verified
Purchased $1-$500
Purchased $500-$5,000
Purchased more than $5,000
You have already submitted a
proposal to this job